455217
110
Zoom out
Zoom in
Vorherige Seite
1/128
Nächste Seite
Additional information12
110
En
Important information regarding the HDMI connection
There are cases where you may not be able to
route HDMI signals through this receiver (this
depends on the HDMI-equipped component
you are connecting–check with the
manufacturer for HDMI compatibility
information).
If you aren’t receiving HDMI signals properly
through this receiver (from your component),
please try one of the following configurations
when connecting up.
Configuration A
Use component video cables to connect the
video output of your HDMI-equipped
component to the receiver’s component video
input. The receiver can then convert the analog
component video signal to a digital HDMI
signal for transmission to the display. For this
configuration, use the most convenient
connection (digital is recommended) for
sending audio to the receiver. See the
operating instructions for more on audio
connections.
Note
•The picture quality will change slightly
during conversion.
No sound, or sound suddenly
ceases.
• Check that the HDMI AV setting is set to AMP/THROUGH.
• If the component is a DVI device, use a separate connection for the audio.
• If analog video is being output over HDMI, please use a separate connection
for the audio.
• Check the audio output settings of the source component.
Noisy or distorted picture. Sometimes a video deck may output a noisy video signal (during scanning,
for example), or the video quality may just be poor (with some video game units,
for example). The picture quality may also depend on the settings, etc. of your
display device. Switch off the video converter and reconnect the source and
display device using the same type of connection (component or composite),
then start playback again.
• If the problem still persists when connecting your HDMI component directly
to your monitor, please consult the component or monitor manual or contact
the manufacturer for support.
HDCP ERROR shows in the
display.
• Check whether or not the connected component is compatible with HDCP. If
it is not compatible with HDCP, reconnect the source device using a different
type of connection (component or composite). Some components that are
compatible with HDCP still cause this message to be displayed, but so long as
there is no problem with displaying video, this is not a malfunction.
Amp-linked operation not
possible using KURO LINK
function.
• Check the HDMI connections.
• The cable may be damaged.
• Select ON for the KURO LINK setting (see KURO LINK Setup on page 62).
• Turn the TV’s power on before turning on this receiver’s power.
• Set the TV side KURO LINK setting to ON.
Symptom Remedy
VSX-1019_KU.book 110 ページ 2009年2月17日 火曜日 午前11時56分
110

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Pioneer VSX-1019AH-K wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Pioneer VSX-1019AH-K

Pioneer VSX-1019AH-K Bedienungsanleitung - Deutsch - 127 seiten

Pioneer VSX-1019AH-K Bedienungsanleitung - Holländisch - 127 seiten

Pioneer VSX-1019AH-K Bedienungsanleitung - Französisch - 127 seiten

Pioneer VSX-1019AH-K Bedienungsanleitung - Italienisch - 127 seiten

Pioneer VSX-1019AH-K Bedienungsanleitung - Spanisch - 127 seiten

Pioneer VSX-1019AH-K Bedienungsanleitung - Schwedisch, Norwegisch, Finnisch - 251 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info