Bedienungsanleitung Pioneer VSX-1021K (Seite 16 von 156) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

455184

Zoom out

Zoom in

Vorherige Seite

1/156

Nächste Seite

2 Connect the microphone to the MCACC

SETUP MIC jack on the front panel.

CONTROL ON

OFF

MCACC

SETUP MIC

iPod

iPhone

iPad

USB

5V 2.1

HDMI 2 INPUT

Microphone

Tripod

Make sure there are no obstacles between the

speakers and the microphone.

If you have a tripod, use it to place the micro-

phone so that it’s about ear level at your

normal listening position. If you do not have

a tripod, use some other object to install the

microphone.

Install the microphone on a stable floor.

Placing the microphone on any of the following

surfaces may make accurate measurement

impossible:

! Sofas or other soft surfaces.

! High places such as tabletops and sofa tops.

The Full Auto MCACC display appears once the

microphone is connected.

Speaker System : Normal

(

SB/FH

)

1a.Full Auto MCACC

A/V RECEIVER

Ex it Re turn

START

EQ Type : SYMMETRY

MCACC : M1.MEMORY 1

THX Speaker : NO

! If you leave the GUI screen for over five

minutes, the screen saver will appear.

3 Select the parameters you want to set.

! When data measurement is taken, the

reverb characteristics data (both before- and

after-calibration) that this receiver had been

storing will be overwritten.

! When measurement is taken of the reverb

characteristics data other than SYMMETRY,

the data are not measured after the

correction. If you will need to measure after

correcting data, take the measurement

using the EQ Professional menu in the

Manual MCACC setup.

If the speakers are connected using any setup

other than Normal(SB/FH), be sure to set

Speaker System before the Full Auto MCACC

Setup. See Speaker system setting on Operating

Instructions in CD-ROM.

! Speaker System – Shows the current

settings. When this is selected and ENTER is

pressed, the speaker system selection screen

appears. Select the proper speaker system,

then press RETURN to return.

If you are planning on bi-amping your front

speakers, or setting up a separate speaker

system in another room, read through

Speaker system setting on Operating

Instructions in CD-ROM and make sure to

connect your speakers as necessary before

continuing to step 4.

! EQ Type – This determines how the

frequency balance is adjusted.

! MCACC – The six MCACC presets are used

for storing surround sound settings for

different listening positions. Simply choose

an unused preset for now.

! THX Speaker – Select YES when using THX

speakers (all speakers other than the front

speakers are set to SMALL). In other cases,

leave at NO.

4 Press then select START.

03 Basic Setup

Basic Setup

Canceling the demo display

On this receiver, the demo mode is turned on by

default. When the power is turned on, the demo

display is set and various indications are shown

on the front panel display. To cancel the demo

display, connect the power cord, then perform

the operation below.

! The demo mode is canceled automatically

when the Full Auto MCACC operation is

performed.

1 Switch the receiver into standby.

2 While holding down ENTER on the

front panel, press u STANDBY/ON.

The display shows RESET c NO d.

3 Select ‘FL DEMO’ using TUNE i/j.

4 Use PRESET k/l to select FL DEMO

c OFF d then press ENTER on the front

panel.

Automatically conducting

optimum sound tuning (Full

Auto MCACC)

The Full Auto MCACC Setup measures the

acoustic characteristics of your listening area,

taking into account ambient noise, speaker

connection and speaker size, and tests for both

channel delay and channel level. After you have

set up the microphone provided with your sys-

tem, the receiver uses the information from a

series of test tones to optimize the speaker set-

tings and equalization for your particular room.

Important

! Make sure the microphone and speakers are

not moved during the Full Auto MCACC Setup.

! Using the Full Auto MCACC Setup will

overwrite any existing settings for the MCACC

preset you select.

! Before using the Full Auto MCACC Setup, the

headphones should be disconnected.

CAUTION

! The test tones used in the Full Auto MCACC

Setup are output at high volume.

THX

! THX is a trademark of THX Ltd., which may

be registered in some jurisdictions. All rights

reserved.

1 Press u RECEIVER to switch on the

receiver and your TV.

Make sure that the TV’s video input is set to this

receiver.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer VSX-1021K Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer VSX-1021K

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info