Bedienungsanleitung Pioneer VSX-1122K (Seite 90 von 107) (Englisch)

491802

Zoom out

Zoom in

Vorherige Seite

1/107

Nächste Seite

FAQ

Symptom Remedy

No picture. Try changing the Resolution setting (in Setting the Video options on page 60).

No sound, or sound suddenly

ceases.

Check that the HDMI Audio setting is set to AMP (Setting the Audio options on page 58).

If the component is a DVI device, use a separate connection for the audio.

If analog video is being output over HDMI, please use a separate connection for the

audio.

Check the audio output settings of the source component.

HDMI format digital audio transmissions require a longer time to be recognized. Due

to this, interruption in the audio may occur when switching between audio formats or

beginning playback.

Turning on/off the device connected to this unit’s HDMI OUT terminal during playback,

or disconnecting/connecting the HDMI cable during playback, may cause noise or inter-

rupted audio.

Noisy or distorted picture. Sometimes a video deck may output a noisy video signal (during scanning, for example),

or the video quality may just be poor (with some video game units, for example). The

picture quality may also depend on the settings, etc. of your display device. Switch off

the video converter and reconnect the source and display device using the same type of

connection (component or composite), then start playback again.

If the problem still persists when connecting your HDMI component directly to your

monitor, please consult the component or monitor manual or contact the manufacturer

for support.

HDCP ERROR shows in the display. Check whether or not the connected component is compatible with HDCP. If it is not

compatible with HDCP, reconnect the source device using a different type of connection

(component or composite). Some components that are compatible with HDCP still cause

this message to be displayed, but so long as there is no problem with displaying video,

this is not a malfunction.

Synchronized operation not possible

using Control with HDMI function.

Check the HDMI connections.

The cable may be damaged.

Select ON for the Control Mode with HDMI setting (see HDMI Setup on page 55).

Turn the TV’s power on before turning on this receiver’s power.

Set the TV side Control with HDMI setting to on (see TV’s operating instructions).

AVNavigator

Symptom Causes Remedy

AVNavigator cannot be

installed.

An error message may appear

if there are not enough system

resources available.

Re-start the PC, then start install with no other applications

active.

Installation of AVNavigator may fail

because of incompatibilities with

other applications.

Try the following, in the order indicated.

1. If there are any other applications active, exit the other

applications and try to start install again.

2. If that does not work, try restarting your PC, then start

install with no other applications active.

Symptom Causes Remedy

AVNavigator does not inter-

act well with the receiver.

The receiver’s power is not turned

on.

Turn the receiver’s power on. (Wait about 60 seconds after

the power turns on for network functions to start.)

After this, press Detection in AVNavigator to redetect the

receiver.

The receiver or computer is not con-

nected to the LAN.

Connect a LAN cable to the receiver or computer (page 29).

After this, press Detection in AVNavigator to redetect the

receiver.

The router’s power is off. Turn the router’s power on.

After this, press Detection in AVNavigator to redetect the

receiver.

AVNavigator’s network settings are

not correct.

If your router does not support DHCP or UPnP, the receiv-

er’s IP address must be set in AVNavigator. First set the

IP address on the receiver, then set the same address in

AVNavigator (page 82).

After this, press Detection in AVNavigator to redetect the

receiver.

Network connections could be

restricted due to the computer’s net-

work settings, security settings, etc.

Check the computer’s network settings, security settings,

etc.

After this, press Detection in AVNavigator to redetect the

receiver.

When the operating instructions

interactive mode is changed, the

settings may not be transferred to

the browser, causing AVNavigator to

stop interacting.

Either refresh the page’s display using the browser’s

refresh button or display a different page from the links so

that the setting is transferred.

When the Wiring Navi,

Operation Guide,

Interactive Manual, Glossary

or Software Update is

launched, a warning about

security protection appears

on the browser.

This is because of the browser’s

security function.

This is not a problem. Perform the operation to authorize

the blocked contents.

Operation Guide does not

display properly.

Adobe Flash Player 10 is not

installed, or its version is too old.

Download Adobe Flash Player from the Adobe site (http://

www.adobe.com/downloads/). If your version is old, update

it.

Software updating does not

operate well.

There may be a problem with your

Internet Service Provider’s network.

Contact your contracted provider.

USB interface

Symptoms Causes Remedies

The folders/files stored on a

USB memory device are not

displayed.

The folders/files are currently stored

in a region other than the FAT (File

Allocation Table) region.

Store the folders/files in the FAT region.

The number of levels in a folder is

more than 9.

Limit the maximum number of levels in a folder to 9 (page

40).

The audio files are copyrighted.

Copyrighted audio files stored on a USB memory device

cannot be played back (page 40).

Pioneer VSX-1122K Seite 90

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer VSX-1122K

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info