Bedienungsanleitung Pioneer VSX-1123-K (Seite 97 von 113) (Englisch)

574087

Zoom out

Zoom in

Vorherige Seite

1/113

Nächste Seite

FAQ

Symptom Causes Remedy

AVNavigator does not inter-

act well with the receiver.

The receiver’s power is not turned

on.

Turn the receiver’s power on. (Wait about 60 seconds after

the power turns on for network functions to start.)

After this, press Detection in AVNavigator to redetect the

receiver.

To turn this unit’s power on and off from the Interactive

Manual, set Network Standby at HOME MENU d

Network Setup to ON.

The receiver or computer is not con-

nected to the LAN.

Connect a LAN cable to the receiver or computer (page 31).

After this, press Detection in AVNavigator to redetect the

receiver.

The router’s power is off. Turn the router’s power on.

After this, press Detection in AVNavigator to redetect the

receiver.

AVNavigator’s network settings are

not correct.

If your router does not support DHCP or UPnP, the receiv-

er’s IP address must be set in AVNavigator. First set the

IP address on the receiver, then set the same address in

AVNavigator (page 86).

After this, press Detection in AVNavigator to redetect the

receiver.

Network connections could be

restricted due to the computer’s net-

work settings, security settings, etc.

Check the computer’s network settings, security settings,

etc.

After this, press Detection in AVNavigator to redetect the

receiver.

When the operating instructions

interactive mode is changed, the

settings may not be transferred to

the browser, causing AVNavigator to

stop interacting.

Either refresh the page’s display using the browser’s

refresh button or display a different page from the links so

that the setting is transferred.

When the Wiring Navi,

Operation Guide,

Interactive Manual or

Glossary is launched, a

warning about security

protection appears on the

browser.

This is because of the browser’s

security function.

This is not a problem. Perform the operation to authorize

the blocked contents.

Software updating does not

operate well.

There may be a problem with your

Internet Service Provider’s network.

Contact your contracted provider.

USB interface

Symptoms Causes Remedies

The folders/files stored on a

USB memory device are not

displayed.

The folders/files are currently stored

in a region other than the FAT (File

Allocation Table) region.

Store the folders/files in the FAT region.

The number of levels in a folder is

more than 9.

Limit the maximum number of levels in a folder to 9 (page

43).

The audio files are copyrighted.

Copyrighted audio files stored on a USB memory device

cannot be played back (page 43).

Symptoms Causes Remedies

A USB memory device is

not recognized.

The USB memory device does not

support the mass storage class

specifications.

Try using a USB memory device compatible with the mass

storage class specifications. Note that there are cases

where even the audio files stored on a USB memory device

compatible with the mass storage class specifications are

not played back on this receiver (page 43).

Connect the USB memory device and switch on this

receiver (page 33).

A USB hub is currently being used.

This receiver does not support USB hubs (page 43).

This receiver recognizes the USB

memory device as a fraud.

Switch off and on again this receiver.

Reconnect the USB device with the receiver switched off.

Change to an input other than iPod/USB, then set the input

back to iPod/USB.

A USB memory device is

connected and displayed,

but the audio files stored

on the USB memory device

cannot be played back.

Some formats of USB memory

devices, including FAT 12, NTFS, and

HFS, cannot be played back on this

receiver.

Check whether the format of your USB memory device is

either FAT 16 or FAT 32. Note that the FAT 12, NTFS, and

HFS formats cannot be played back on this receiver (page

43).

The file format cannot be properly

played back on this receiver.

See the list of file formats that can be played back on this

receiver (page 44).

iPod

Symptoms Causes Remedies

iPod is not recognized. This receiver recognizes the iPod as

a fraud.

Switch off and on again this receiver.

Reconnect the iPod with the receiver switched off.

Change to an input other than iPod/USB, then set the input

back to iPod/USB.

Network

Symptoms Causes Remedies

Cannot access the network. The LAN cable is not firmly con-

nected.

Firmly connect the LAN cable (page 31).

The router is not switched on. Switch on the router.

Internet security software is cur-

rently installed in the connected

component.

There are cases where a component with Internet security

software installed cannot be accessed.

The audio component on the net-

work which has been switched off is

switched on.

Switch on the audio component on the network before

switching on this receiver.

Playback does not start

while “Connecting...” con-

tinues to be displayed.

The component is currently discon-

nected from this receiver or the

power supply.

Check whether the component is properly connected to

this receiver or the power supply.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer VSX-1123-K Seite 97

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer VSX-1123-K

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info