Bedienungsanleitung Pioneer VSX-30 (Seite 113 von 136) (Englisch)

574064

113

Zoom out

Zoom in

Vorherige Seite

1/136

Nächste Seite

Additional information 12

113

No sound

AMP ERR blinks in the

display, then the power

automatically switches off.

The ADVANCED MCACC

blinks and the power does

not turn on.

• The receiver may have a serious problem. Do not try switching the receiver

on. Unplug the receiver from the wall and call a Pioneer authorized

independent service company.

The blue indicator (at the

center of the receiver) flashes

and power turns off.

• There is a problem with the receiver’s power unit. The receiver may have a

serious problem. Unplug the receiver from the wall and call a Pioneer

authorized independent service company.

AMP OVERHEAT and the

blue indicator (at the center

of the receiver) flash and the

power turns off.

• Allow the unit to cool down in a well-ventilated place before switching back

on.

• Wait at least 1 minute, then try turning the power on again.

The receiver suddenly power

off or PQLS flashes.

• The power unit is damaged. Unplug the receiver from the wall and call a

Pioneer authorized independent service company.

Display blinks 12V TRG ERR. • An error has arisen in the 12 V trigger jacks. Reconnect accurately then turn

the power back on.

Symptom Remedy

No sound is output when an

input function is selected.

No sound is output from the

front speakers.

• Check the volume, mute setting (press MUTE) and speaker setting (press

SPEAKERS).

• Make sure the correct input function is selected.

• Check that the MCACC setup microphone is disconnected.

• Make sure the correct input signal is selected (press SIGNAL SEL). Note that

when PCM is selected, you won’t be able to hear any other signal format.

• Check that the source component is connected properly (see Connecting

your equipment on page 15).

• Check that the speakers are connected properly (see Connecting the speakers

on page 20).

No sound from the surround

or center speakers.

• Check that the Stereo listening mode or the Front Stage Surround Advance

mode isn’t selected; select one of the surround listening modes (see Listening

in surround sound on page 61).

• Check that the surround/center speakers are not set to NO (see Speaker

Setting on page 106).

• Check the channel level settings (see Channel Level on page 107).

• Check the speaker connections (see Connecting the speakers on page 20).

No sound from surround

back speakers.

• Check that the surround back speakers are set to LARGE or SMALL, and the

surround speakers are not set to NO (see Speaker Setting on page 106).

• Check the speaker connections (see Connecting the speakers on page 20).

If only one surround back speaker is connected, make sure it’s connected to

the left channel speaker terminal.

• Surround back speakers will not play while the Speaker System is set to

Speaker B and audio is being played through speaker B.

VSX-31_30_UC.book 113 ページ２０１０年８月２５日　水曜日　午前９時２８分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer VSX-30 Seite 113

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info