Bedienungsanleitung Pioneer VSX-30 (Seite 115 von 136) (Englisch)

574064

115

Zoom out

Zoom in

Vorherige Seite

1/136

Nächste Seite

Additional information 12

115

Other audio problems

Symptom Remedy

Broadcast stations cannot be

selected automatically, or

there is considerable noise in

radio broadcasts.

For FM broadcasts

• Fully extend the FM wire antenna, adjust the position for best reception and

secure to a wall, etc.

• Use an outdoor antenna for better reception (see page 31).

For AM broadcasts

• Adjust the position and direction of the AM antenna.

• Use an outdoor antenna for better reception (see page 31).

• Noise may be caused by interference from other equipment, such as a

fluorescent light, motor, etc. Switch off or move the other equipment, or move

the AM antenna.

Noise is output when

scanning a DTS CD.

• This is not a malfunction of the receiver. The scan function of your player

alters the digital information, making it unreadable, resulting in noise being

output. Lower the volume when scanning.

When playing a DTS format

LD there is audible noise on

the soundtrack.

• Make sure that the input signal type is set to DIGITAL (see Choosing the input

signal on page 65).

Can’t record audio. • You can only make a digital recording from a digital source, and an analog

recording from an analog source.

• For digital sources, make sure that what you’re recording isn’t copy protected.

• Check that the OUT jacks are properly connected to the recorders input jacks

(see Connecting other audio components on page 30).

Subwoofer output is very low. • To route more signal to the subwoofer, set it to PLUS or set the front speakers

to SMALL (see Speaker Setting on page 106).

Everything seems to be set up

correctly, but the playback

sound is odd.

• The speakers may be out of phase. Check that the positive/negative speaker

terminals on the receiver are matched with the corresponding terminals on the

speakers (see Connecting the speakers on page 20).

The PHASE CONTROL

feature doesn’t seem to have

an audible effect.

• If applicable, check that the lowpass filter switch on your subwoofer is off, or

the lowpass cutoff is set to the highest frequency setting. If there is a PHASE

setting on your subwoofer, set it to 0º (or depending on the subwoofer, the

setting where you think it has the best overall effect on the sound).

• Make sure the speaker distance setting is correct for all speakers (see Speaker

Distance on page 107).

Noise or hum can be heard

even when there is no sound

being input.

• Check that personal computers or other digital components connected to the

same power source are not causing interference.

Can’t select some Input

functions by the INPUT

SELECTOR on the front panel

or the INPUT SELECT button

on the remote control.

• Check the Input Skip settings in the Input Setup menu.

• Check the HDMI Input assignment in the Input Setup menu then try OFF.

There seems to be a time lag

between the speakers and

the output of the subwoofer.

• See Automatically conducting optimum sound tuning (Auto MCACC on

page 41 to set up your system again using MCACC (this will automatically

compensate for a delay in the subwoofer output).

VSX-31_30_UC.book 115 ページ２０１０年８月２５日　水曜日　午前９時２８分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer VSX-30 Seite 115

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info