Bedienungsanleitung Pioneer VSX-9120TXH-k (Seite 75 von 88) (Englisch)

574198

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

Additional information

Video

Settings

Can’t record audio. • You can only make a digital recording from a digital source, and an analog recording from an analog

source.

• For digital sources, make sure that what you’re recording isn’t copy protected.

• Check that the

OUT

jacks are properly connected to the recorders input jacks (see

Connecting analog

audio sources

on page 16).

Subwoofer output is very low. • To route more signal to the subwoofer, set it to

PLUS

or set the front speakers to

SMALL

(see

Speaker

Setting

on page 43).

Everything seems to be set up

correctly, but the playback sound

is odd.

• The speakers may be out of phase. Check that the positive/negative speaker terminals on the receiver are

matched with the corresponding terminals on the speakers (see

Connecting the speakers

on page 17).

The

PHASE CONTROL

feature

doesn’t seem to have an audible

effect.

• If applicable, check that the lowpass filter switch on your subwoofer is off, or the lowpass cutoff is set to

the highest frequency setting. If there is a

PHASE

setting on your subwoofer, set it to 0º (or depending on

the subwoofer, the setting where you think it has the best overall effect on the sound).

• Make sure the speaker distance setting is correct for all speakers (see

Speaker Distance

on page 45).

Noise or hum can be heard even

when there is no sound being

input.

• Check that personal computers or other digital components connected to the same power source are not

causing interference.

There seems to be a time lag

between the speakers and the

output of the subwoofer.

• See

Automatically setting up for surround sound (Auto MCACC)

on page 8 to set up your system again

using MCACC (this will automatically compensate for a delay in the subwoofer output).

The maximum volume available

(shown in the front panel display)

is lower than the

+12dB

maximum.

• This is not a malfunction. If the levels in

Channel Level

on page 44 have been adjusted, the maximum

volume will change accordingly.

Symptom

Remedy

Symptom Remedy

No image is output when an input

is selected.

• Check the video connections of the source component (see page 14).

• For high-definition video (using component video connections), or when digital video conversion is

switched off (in

Setting the AV options

on page 63), you must connect your TV to this receiver using the same

type of video cable as you used to connect your video component.

• Make sure the input assignment is correct for components connected using component or HDMI cables

(see

The Input Setup menu

on page 60).

• Check the video output settings of the source component.

• Check that the video input you selected on your TV is correct.

Can’t record video. • Check that the source is not copy-protected.

• The video converter is not available when making recordings. Check that the same type of video cable is

used for connecting both the recorder and the video source (the one you want to record) to this receiver.

Noisy, intermittent, or distorted

picture.

• Sometimes a video deck may output a noisy video signal (during scanning, for example), or the video

quality may just be poor (with some video game units, for example). The picture quality may also depend on

the settings, etc. of your display device. Switch off the video converter and reconnect the source and display

device using the same type of connection (component, S-video or composite), then start playback again.

Symptom Remedy

The Auto MCACC Setup

continually shows an error.

• The ambient noise level may be too high. Keep the noise level in the room as low as possible (see also

Problems when using the Auto MCACC Setup

on page 10). If the noise level cannot be kept low enough, you

will have to set up the surround sound manually (page 37).

After using the Auto MCACC

Setup, the speaker size setting is

incorrect.

• There may have been some low frequency noise in the room from an air-conditioner, motor, etc. Switch

off all other appliances in the room and use Auto MCACC Setup again.

• Depending on a number of factors (room size, speaker placement, etc.) this may occur in some cases.

You can change the speaker setting manually in

Speaker Setting

on page 43, and use the

ALL (Keep

SPsetting)

option for the

Auto Mode

Automatic MCACC (Expert)

on page 34 if this is a recurring

problem.

VSX-9120TXH_KU.book 75 ページ２００７年４月１２日　木曜日　午前１１時４７分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer VSX-9120TXH-k Seite 75

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer VSX-9120TXH-k

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info