Bedienungsanleitung Pioneer VSX-9140TXH (Seite 98 von 123) (Englisch)

574068

Zoom out

Zoom in

Vorherige Seite

1/123

Nächste Seite

Additional information

Positional relationship between speakers

and monitor

Position of front speakers and monitor

The front speakers should be as equidistant as possible

to the monitor.

Position of center speaker and monitor

Since mostly dialogs are output from the center speaker,

keeping the center speaker as close as possible to the

screen makes the overall sound more natural. For TVs

using Braun tubes, however, when installing the center

speaker on the floor, adjust its angle of elevation to point

it towards the listening position.

•If the center speaker is not of the shielded type, install

it away from the TV.

• When installing the center speaker on top of the

monitor, place it facing slightly downwards towards

the listening position.

Troubleshooting

Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with

this component, check the points below. Sometimes the trouble may lie in another component. Investigate the other

components and electrical appliances being used. If the trouble cannot be rectified even after exercising the checks

listed below, ask your nearest Pioneer authorized independent service company to carry out repair work.

Note

• If the unit does not operate normally due to external effects such as static electricity disconnect the power plug

from the outlet and insert again to return to normal operat

ing conditions.

Power

monitor

45° to 60°

Installation on floor

(Diagram as seen

from the side)

Monitor

Symptom Remedy

The power does not turn on. • Make sure that the power cord is plugged in to an active power outlet.

• Try disconnecting from the power outlet, then plugging back in.

Power cannot be turned off.

(ZONE 2 ON or ZONE 3 ON

(VSX-9140TXH only) is

displayed.)

• Set the remote control’s MULTI-ZONE operation selector switch to ZONE 2 or ZONE 3 (VSX-

9140TXH only), then press  RECEIVER to switch the sub zone off.

The receiver suddenly switches

off or the PHASE CONTROL

indicator blinks.

• Check that there are no loose strands of speaker wire t

ouching the rear panel or another set of

wires. If so, re-attach the speaker wires, making sure there are no stray strands.

• The receiver may have a serious problem. Disconnect from the power and call a Pioneer authorized

independent service company.

During loud playback the

power suddenly switches off.

• Turn down the volume.

• Lower the 63 Hz and 125 Hz equalizer levels in the Manual MCACC setup on page 80.

• Switch on the digital safety feature. While holding down ENTER on the front panel, press

 STANDBY/ON to set this receiver to the standby mode. Use TUNE +/– to select D.SAFETY

OFF, and then use PRESET +/– to select 1 or 2 (select D.SAFETY OFF to deactivate this

feature). If the power switches off even with 2 switched on, turn down the volume. With 1 or 2 on,

some features may be unavailable.

The unit does not respond

when the buttons are pressed.

• Try switching the receiver off, then back on again.

• Try disconnecting the power cord, then connect again.

VSX-9140TXH_CUXJ.book 98 ページ２００９年４月１６日　木曜日　午前１０時３６分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer VSX-9140TXH Seite 98

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info