Bedienungsanleitung Pioneer VSX-9140TXH (Seite 100 von 123) (Englisch)

574068

100

Zoom out

Zoom in

Vorherige Seite

1/123

Nächste Seite

Additional information

100

Other audio problems

No sound from one speaker.• Check the speaker connection (see Connecting the speakers on page 19).

• Check the speaker level settings (see Channel Level on page 92).

• Check that the speaker hasn’t been set to NO (see Speaker Setting on page 91).

• The channel may not be recorded in the source. By using one of the advanced effect listening

mode, you may be able to create the missing channel (see Listening in surround sound on page 56).

Sound is produced from

analog components, but not

from digital ones (DVD, LD,

CD-ROM, etc.).

• Check that the input signal type is set to DIGITAL (see Choosing the input signal on page 61).

• Make sure that the digital input is assigned correctly for the input jack the component is connected

to (see The Input Setup menu on page 43).

• Check the digital output settings on the source component.

• If the source component has a digital volume control, make sure this is not turned down.

• Make sure that the multichannel analog inputs are not selected. Select any other input function.

No sound is output or a noise is

output when Dolby Digital/DTS

software is played back.

• Check that your DVD player is compatible with Dolby Digital/DTS discs.

• Check the digital output settings of your DVD player. Make sure that the DTS signal output is set

to On.

• If the source component has a digital volume control, make sure this is not turned down.

No sound when using the

HOME MENU.

• If the HDMI input function is selected, sound is muted until exiting the HOME MENU.

Symptom Remedy

Broadcast stations cannot be

selected automatically, or

there is considerable noise in

radio broadcasts.

For FM broadcasts

• Fully extend the FM wire antenna, adjust the position for best reception and secure to a wall, etc.

• Use an outdoor antenna for better reception (see page 31).

For AM broadcasts

• Adjust the position and direction of the AM antenna.

• Use an outdoor antenna for better reception (see page 31).

• Noise may be caused by interference from other equipment, such as a fluorescent light, motor,

etc. Switch off or move the other equipment, or move the AM antenna.

A multichannel DVD source

appears to be downmixed to 2

channels during playback.

• Make sure that the multichannel analog inputs are selected (see Selecting the multichannel analog

inputs on page 46).

Noise is output when scanning

a DTS CD.

• This is not a malfunction of the receiver. The scan function of your player alters the digital

information, making it unreadable, resulting in noise being output. Lower the volume when

scanning.

When playing a DTS format LD

there is audible noise on the

soundtrack.

• Make sure that the input signal type is set to DIGITAL (see Choosing the input signal on page 61).

Can’t record audio. • You can only make a digital recording from a digital source, and an analog recording from an

analog source.

• For digital sources, make sure that what you’re recording isn’t copy protected.

• Check that the OUT jacks are properly connected to the recorders input jacks (see Connecting

other audio components on page 29).

Subwoofer output is very low. • To route more signal to the subwoofer, set it to PLUS or set the front speakers to SMALL (see

Speaker Setting on page 91).

Everything seems to be set up

correctly, but the playback

sound is odd.

• The speakers may be out of phase. Check that the positive/negative speaker terminals on the

receiver are matched with the corresponding terminals on the speakers (see Connecting the

speakers on page 19).

The PHASE CONTROL feature

doesn’t seem to have an

audible effect.

• If applicable, check that the lowpass filter switch on your subwoofer is off, or the lowpass cutoff is

set to the highest frequency setting. If there is a PHASE setting on your subwoofer, set it to 0º (or

depending on the subwoofer, the setting where you think it has the best overall effect on the sound).

• Make sure the speaker distance setting is correct for all speakers (see Speaker Distance on

page 93).

Noise or hum can be heard

even when ther e is no sound

being input.

• Check that personal computers or other digital components connected to the same power source

are not causing interference.

Symptom Remedy

VSX-9140TXH_CUXJ.book 100 ページ２００９年４月１６日　木曜日　午前１０時３６分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer VSX-9140TXH Seite 100

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info