Bedienungsanleitung Pioneer VSX-9140TXH (Seite 102 von 123) (Englisch)

574068

102

Zoom out

Zoom in

Vorherige Seite

1/123

Nächste Seite

Additional information

102

Professional Calibration EQ graphical output

Display

After using the Auto MCACC

Setup, the speaker size setting

is incorrect.

• There may have been some low frequency noise in the room from an air-conditioner, motor, etc.

Switch off all other appliances in the room and use Auto MCACC Setup again.

• Depending on a number of factors (room size, speaker placement, etc.) this may occur in some

cases. Change the speaker setting manually in Speaker Setting on page 91, and use the ALL (Keep

SP System) op tion for the Auto MCACC menu in Automatic MCACC (Expert) on page 78 if this is a

recurring problem.

Can’t adjust the Fine Speaker

Distance setting (page 82)

properly.

• Check that the speakers are all in phase (make sure the positive (+) and negative (–) terminals are

matched up properly).

The display shows

KEY LOCK ON

when you try to make settings.

• With the receiver in standby, press  STANDBY/ON while holding down SPEAKERS to disable the

key lock.

Most recent settings have been

erased.

• The power cord was disconnected from the wall while adjusting this setting.

• Settings are only stored if all the zones are turned off. Turn off all the zones before unplugging the

power cord.

The various system settings are

not stored.

• Make sure the blue  STANDBY/ON light has gone out before unplugging.

Symptom Remedy

The EQ response displayed in

the graphical output following

calibration does not appear

entirely flat.

• There are cases where the graph does not appear flat (even when selecting ALL CH ADJ in the Auto

MCACC Setup) due to adjustments made to compensate for room characteristics to achieve optimal

sound.

• Areas of the graph may appear identical (before and after) when there is little or no adjustment

needed.

• The graph may appear to have shifted vertically when comparing before and after measurements.

EQ adjustments made using

the Manual MCACC setup on

page 80 do not appear to

change the graphical output.

• Despite level adjustments being made, the filters used for analysis may not display these

adjustments in the graphical output. However, these adjustments are taken this into account by the

filters dedicated to overall system calibration.

Lower frequency response

curves do not seem to have

been calibrated for SMALL

speakers.

• Low frequencies used in bass management (the subwoofer channel) will not change for speakers

that have been specified as SMALL in the configuration, or do not output these frequencies.

• Calibration is performed, but due to your speakers’ low frequency limitations, no measurable

sound is output for display.

Symptom Remedy

The display is dark or off. • Press DIMMER repeatedly to select a different brightness.

After making an adjustment

the display goes off.

• Press DIMMER repeatedly to select a different brightness.

You can’t get DIGITAL to

display when using SIGNAL

SEL.

• Check the digital connections and make sure that the digital inputs are assigned correctly (see The

Input Setup menu on page 43).

• If the multichannel analog inputs are selected, select a different input function.

2 DIGITAL or DTS does not

light when playing Dolby/DTS

software.

• These indicators does not light if playback is paused.

• Check the playback (especially the digital output) settings of the source component.

When playing Dolby Digital or

DTS sources, the receiver’s

format indicators do not light.

• Check that the player is connected using a digital connection.

• Make sure that the receiver is set to AUTO or DIGITAL (see Choosing the input signal on page 61).

• Check that the player isn’t set up so that Dolby Digital and DTS sources are converted to PCM.

• Ensure that if there are several audio tracks on the disc, the Dolby Digital or DTS is selected.

When playing certain discs,

none of the receiver’s format

indicators light.

• The disc may not contain 5.1/6.1 channel material. Check the disc packaging for more on what

audio tracks are recorded on the disc.

When playing a disc with the

listening mode set to Auto

Surround or ALC, 2 PL II or

Neo:6 appear on the receiver.

• Make sure that the receiver is set to AUTO or DIGITAL (see Choosing the input signal on page 61).

• If a two channel soundtrack is currently playing (including Dolby Surround encoded), then this is

not a malfunction. Check the disc packaging for details about the audio tracks available.

Symptom Remedy

VSX-9140TXH_CUXJ.book 102 ページ２００９年４月１６日　木曜日　午前１０時３６分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer VSX-9140TXH Seite 102

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info