Bedienungsanleitung Pioneer VSX-9140TXH (Seite 101 von 123) (Englisch)

574068

101

Zoom out

Zoom in

Vorherige Seite

1/123

Nächste Seite

Additional information

101

Video

Settings

Can’t select some Input

functions by the INPUT

SELECTOR on the front panel

or the INPUT SELECT button on

the remote control.

• Make sure that the Input Skip settings in the INPUT SETUP menu.

• Make sure that the HDMI Input assign in the INPUT SETUP menu then try OFF.

There seems to be a time lag

between the speakers and the

output of the subwoofer.

• See Automatically setting up for surround sound (Auto MCACC) on page 41 to set up your system

again using MCACC (this will automatically compensate for a delay in the subwoofer output).

The maximum volume

available (shown in the front

panel display) is lower than the

+12dB maximum.

• Check that the Volume Limit is set to OFF (see Volume Limit Setup on page 95).

Symptom Remedy

No image is output when an

input is selected.

• Check the video connections of the source component (see page 28).

• For HDMI, or when digital video conversion is set to OFF and a TV and another component are

connected with different cords (in Setting the Video options on page 68), you must connect your TV

to this receiver using the same type of video cable as you used to connect your video component.

• Make sure the input assignment is correct for components connected using component video,

HDMI or S-Video cables (see The Input Setup menu on page 43).

• Check the video output settings of the source component.

• Check that the video input you selected on your TV is correct.

• Some components (such as video game units) have resolutions that may not be converted. If

adjusting this receiver’s Resolution setting (in Setting the Video options on page 68) and/or the

resolution settings on your component or display doesn’t work, try switching Digital Video

Conversion (in Setting the Video options on page 68) OFF.

Can’t record video. • Check that the source is not copy-protected.

• The video converter is not available when making recordings. Check that the same type of video

cable is used for connecting both the recorder and the video source (the one you want to record) to

this receiver.

Noisy, intermittent, or distorted

picture.

• Sometimes a video deck may output a noisy video signal (during scanning, for example), or the

video quality may just be poor (with some video game units, for example). The picture quality may

also depend on the settings, etc. of your display device. Switch off the video converter and reconnect

the source and display device using the same type of connection (component, S-Video or

composite), then start playback again.

Video signals are not output

from the component terminal.

• When a monitor only compatible with resolutions of 480i is connected to the component terminal

and another monitor is connected to the HDMI terminal, the video signals may not be output to the

monitor connected to the component terminal. If this happens, do the following:

– Turn off the power of the monitor connected to the HDMI terminal.

– Set RES on the VIDEO PARAMETER menu to PURE (page 68).

Symptom Remedy

The Auto MCACC Setup

continually shows an error.

• The ambient noise level may be too high. Keep the noise level in the room as low as possible (see

also Problems when using the Auto MCACC Setup on page 43). If the noise level cannot be kept low

enough, you will have to set up the surround sound manually (page 90).

• When using only one surround back speaker, connect it to the SURROUND BACK L (Single)

terminals.

• To use a 5.1-channel speaker set, use the surround speakers for the surround channel, not the

surround back channel.

• Make sure there are no obstacles between the speakers and the microphone.

• If Reverse Phase is displayed, try the following:

– The speaker’s wiring (+ and –) may be inverted. Check the speaker connections.

–

Depending on the type of speakers and their installation conditions,

Reverse Phase

may be

displayed even if the speakers are properly connected. If this happens, select

GO NEXT

and continue.

– If the speaker is not pointed to the microphone (listening position) or when using speakers that

affect the phase (dipole speakers, reflective speakers, etc.), it may not be possible to properly identify

the polarity.

Symptom Remedy

VSX-9140TXH_CUXJ.book 101 ページ２００９年４月１６日　木曜日　午前１０時３６分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer VSX-9140TXH Seite 101

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info