Bedienungsanleitung Pioneer VSX-920-K (Seite 40 von 400) (Englisch, Französisch)

574201

Zoom out

Zoom in

Vorherige Seite

1/400

Nächste Seite

Basic Setup04

THX

THX is a trademark of THX Ltd., which may be

registered in some jurisdictions. All rights

reserved.

1 Switch on the receiver and your TV.

2 Connect the microphone to the

MCACC

SETUP MIC

jack on the front panel.

Make sure there are no obstacles between the

speakers and the microphone.

If you have a tripod, use it to place the

microphone so that it’s about ear level at your

normal listening position. If you do not have a

tripod, use some other object to install the

microphone.

The Full Auto MCACC display appears once the

microphone is connected.

3 Select the parameters you want to set.

If the speakers are connected using any setup

other than the Front height setup, be sure to

set Speaker System before the Auto MCACC

Setup. See Speaker system setting on

page 101.

• Speaker System

– Select your speaker

system setting.

• EQ Type – This determines how the

frequency balance is adjusted.

• MCACC – The six MCACC presets are used

for storing surround sound settings for

different listening positions. Simply choose

an unused preset for now (you can rename

it later in Data Management on page 98).

• THX Speaker – Select YES if you are using

THX speakers (set all speakers to SMALL),

otherwise leave it set to NO.

Note

1 Install the microphone on a stable floor. Placing the microphone on any of the following surfaces may make accurate

measurement impossible:

• Sofas or other soft surfaces.

• High places such as tabletops and sofa tops.

MASTER

VOLUME

MCACC

SETUP MIC

VIDEO CAMERA

iPod

iPhone

USB HDMI 5

CONTROL ON

OFF

Microphone

Tripod

VSX-1020/VSX-1025

2 If you leave the GUI screen for over five minutes, the screen saver will appear.

3 • When data measurement is taken, the reverb characteristics data (both before- and after-calibration) that this

receiver had been storing will be overwritten. If you want to save the reverb characteristics data before measuring,

connect a USB memory device to this receiver and transfer the data.

• When measurement is taken of reverb characteristics data other than SYMMETRY, the data are not measured after

the correction. If you will need to measure after correcting data, take the measurement using the EQ Professional

menu in the Manual MCACC setup (page 93).

4 If you are planning on bi-amping your front speakers, or setting up a separate speaker system in another room, read

through Speaker system setting on page 101 and make sure to connect your speakers as necessary before continuing

to step 4.

Speaker System : Normal

(

SB/FH

)

1a.Full Auto MCACC

A/V RECEIVER

Exit Return

START

EQ Type : SYMMETRY

MCACC : M1.MEMORY 1

THX Speaker : NO

VSX-1020_SYXCN.book 40 ページ２０１０年３月１２日　金曜日　午前９時１０分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer VSX-920-K Seite 40

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer VSX-920-K

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info