Bedienungsanleitung Pioneer VSX-920-K (Seite 41 von 400) (Englisch, Französisch)

574201

Zoom out

Zoom in

Vorherige Seite

1/400

Nächste Seite

Basic Setup 04

English

Français

Deutsch

Nederlands

Italiano

Español

4 Press and then select

START

5 Follow the instructions on-screen.

Make sure the microphone is connected, and if

you’re using a subwoofer, make sure it is

switched on and set to a comfortable volume

level.

6 Wait for the test tones to finish, then

confirm the speaker configuration in the GUI

screen.

A progress report is displayed on-screen while

the receiver outputs test tones to determine the

speakers present in your setup. Try to be as

quiet as possible while it’s doing this.

If no operations are performed for 10 seconds

while the speaker configuration check screen

is being displayed, the Auto MCACC Setup will

resume automatically. In this case, you don’t

need to select ‘OK’ and press ENTER in step 7.

• With error messages (such as Too much

ambient noise! or Check microphone.),

select RETRY after checking for ambient

noise (see Problems when using the Auto

MCACC Setup on page 42) and verifying the

mic connection. If there doesn’t seem to be

a problem, you can simply select GO NEXT

and continue.

The configuration shown on-screen should

reflect the actual speakers you have.

•If you see an ERR message (or the speaker

configuration displayed isn’t correct),

there may be a problem with the speaker

connection.

If selecting RETRY doesn’t work, turn off

the power and check the speaker

connections. If there doesn’t seem to be a

problem, you can simply use / to

select the speaker and / to change

the setting and continue.

•If Reverse Phase is displayed, the

speaker’s wiring (+ and –) may be

inverted. Check the speaker connections.

– If the connections were wrong, turn off

the power, disconnect the power cord,

then reconnect properly. After this,

perform the Full Auto MCACC procedure

again.

– If the connections were right, select GO

NEXT and

continue.

7 Make sure ‘

’ is selected, then press

ENTER

A progress report is displayed on-screen while

the receiver outputs more test tones to

determine the optimum receiver settings for

Channel Level, Speaker Distance, Standing

Wave and Acoustic Cal EQ.

Again, try to be as quiet as possible while this

is happening. It may take 3 to 10 minutes.

8 The Auto MCACC Setup procedure is

completed and the

Home Menu

reappears automatically.

Be sure to disconnect the microphone from

this receiver upon completion of the Auto

MCACC Setup.

Note

1 Do not adjust the volume during the test tones. This may result in incorrect speaker settings.

RECEIVER

Now Analyzing... 2/9

Environment Check

1a.Full Auto MCACC

A/V RECEIVER

Exit Cancel

Ambient Noise : OK

Microphone :

Speaker YES/NO :

L : YES

FHL : YES

C : YES

FHR : YES

R : YES

SR : YES

SBR : YES

SBL : YES

SL : YES

SW : YES

1a.Full Auto MCACC

OK RETRY

A/V RECEIVER

Exit Cancel

2 If the speaker is not pointed to the microphone (listening position) or when using speakers that affect the phase

(dipole speakers, reflective speakers, etc.), Reverse Phase may be displayed even if the speakers are properly

connected.

3 You can also choose to view the settings from the MCACC Data Check screen. See Checking MCACC Data on page 96

for more on this.

VSX-1020_SYXCN.book 41 ページ２０１０年３月１２日　金曜日　午前９時１０分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer VSX-920-K Seite 41

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer VSX-920-K

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info