Bedienungsanleitung Pioneer VSX-922S (Seite 87 von 109) (Englisch)

491804

Zoom out

Zoom in

Vorherige Seite

1/109

Nächste Seite

FAQ

Symptom Remedy

No sound from front height or front

wide speakers.

Check that the front height or front wide speakers are set to LARGE or SMALL, and the

surround speakers are not set to NO (see Speaker Setting on page 79).

When Speaker System is set to Normal(SB/FH) or Normal(SB/FW) and SP: SB ON is

selected with the SPEAKERS button, no sound will be output from the front height or

front wide speakers. Select SP: SB/FH ON, SP: SB/FW ON, SP: FH ON or SP: FW ON (see

Switching the speaker terminals on page 61).

Check the speaker connections (see Connecting the speakers on page 18).

No sound from subwoofer. Check that the subwoofer is connected properly, switched on and the volume turned up.

If your subwoofer has a sleep function, make sure it is switched off.

Make sure that the Subwoofer setting is YES or PLUS (see Speaker Setting on page 79).

The crossover frequency may be set too low; try setting it higher to match the characteris-

tics of your other speakers (see Speaker Setting on page 79).

If there is very little low frequency information in the source material, change your

speaker settings to Front: SMALL / Subwoofer: YES, or Front: LARGE / Subwoofer: PLUS

(see Speaker Setting on page 79).

Check that the LFE channel is not set to OFF, or to a very quiet setting (see Setting the

Audio options on page 57).

Check the speaker level settings (see Channel Level on page 80).

No sound from one speaker.

Check the speaker connection (see Connecting the speakers on page 18).

Check the speaker level settings (see Channel Level on page 80).

Check that the speaker hasn’t been set to NO (see Speaker Setting on page 79).

The channel may not be recorded in the source. By using one of the advanced effect

listening modes, you may be able to create the missing channel (see Enjoying various

types of playback using the listening modes on page 45).

Sound is produced from analog

components, but not from digital

ones (DVD, LD, CD, etc.).

Check that the input signal type is set to DIGITAL (see Choosing the input signal on page

46).

Make sure that the digital input is assigned correctly for the input jack the component is

connected to (see The Input Setup menu on page 34).

Check the digital output settings on the source component.

If the source component has a digital volume control, make sure this is not turned down.

No sound is output or a noise is out-

put when Dolby Digital/DTS software

is played back.

Check that your BD or DVD player is compatible with Dolby Digital/DTS discs.

Check the digital output settings or the HDMI audio output settings of your BD or DVD

player. Make sure that the DTS signal output is set to On.

If the source component has a digital volume control, make sure this is not turned down.

No sound when using the

Home Menu.

If the HDMI input function is selected, sound is muted until exiting the Home Menu.

Other audio problems

Symptom Remedy

Speaker switching sound (clicking

sound) is heard from receiver during

playback.

Depending on the listening mode, the front height (or front wide) and surround back

speakers may switch automatically in function of changes in the input audio. A speaker

switching sound (clicking sound) will be heard from the receiver at this time. If this sound

bothers you, we recommend to change the speaker terminal option (see Switching the

speaker terminals on page 61).

Symptom Remedy

Broadcast stations cannot be

selected automatically, or there is

considerable noise in radio broad-

casts.

Fully extend the FM wire antenna, adjust the position for best reception and secure to a

wall, etc.

Use an outdoor antenna for better reception (see page 27).

Adjust the position and direction of the AM antenna.

Noise may be caused by interference from other equipment, such as a fluorescent light,

motor, etc. Switch off or move the other equipment, or move the AM antenna.

Noise is output when scanning a

DTS CD.

This is not a malfunction of the receiver. The scan function of your player alters the digital

information, making it unreadable, resulting in noise being output. Lower the volume

when scanning.

When playing a DTS format LD there

is audible noise on the soundtrack.

Make sure that the input signal type is set to DIGITAL (see Choosing the input signal on

page 46).

Subwoofer output is very low.

To route more signal to the subwoofer, set it to PLUS or set the front speakers to SMALL

(see Speaker Setting on page 79).

Everything seems to be set up cor-

rectly, but the playback sound is odd.

The speakers may be out of phase. Check that the positive/negative speaker terminals on

the receiver are matched with the corresponding terminals on the speakers (see Connect-

ing the speakers on page 18).

The Phase Control feature doesn’t

seem to have an audible effect.

If applicable, check that the lowpass filter switch on your subwoofer is off, or the lowpass

cutoff is set to the highest frequency setting. If there is a PHASE setting on your sub-

woofer, set it to 0º (or depending on the subwoofer, the setting where you think it has the

best overall effect on the sound).

Make sure the speaker distance setting is correct for all speakers (see Speaker Distance

on page 80).

Noise or hum can be heard even

when there is no sound being input.

Check that personal computers or other digital components connected to the same

power source are not causing interference.

Can’t select some Input functions by

the INPUT SELECTOR on the front

panel or the INPUT SELECT button

on the remote control.

Check the Input Skip settings in the Input Setup menu (see The Input Setup menu on

page 34).

Check the HDMI Input assignment in the Input Setup menu then try OFF (see The Input

Setup menu on page 34).

There seems to be a time lag

between the speakers and the output

of the subwoofer.

See Automatically conducting optimum sound tuning (Full Auto MCACC) on page 32 to

set up your system again using MCACC (this will automatically compensate for a delay in

the subwoofer output).

The maximum volume available

(shown in the front panel display) is

lower than the +12dB maximum.

Check that the Volume Limit is set to OFF (see Volume Setup on page 83).

The channel level setting may be over 0.0dB.

Certain listening modes or

HOME MENU items cannot be

selected.

When Operation Mode is set to Basic, the Pioneer-recommended settings are made and

not all of the functions can be used. To use all of the functions without restrictions, set

Operation Mode to Expert (see Operation Mode Setup on page 35).

The volume level drops automati-

cally.

The temperature within the unit has exceeded the allowable value. Try moving the unit for

better ventilation (see Installing the receiver on page 7).

Pioneer VSX-922S Seite 87

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer VSX-922S

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info