Bedienungsanleitung Pioneer VSX-AX5i-S (Seite 109 von 120) (Englisch)

574069

109

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

Techno Tidbits and Problem-solving

109

EXPERT

Troubleshooting

Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong

with this component, check the points below. Sometimes the trouble may lie in another component. Investigate the

other components and electrical appliances being used. If the trouble cannot be rectified even after exercising the

checks listed below, ask your nearest PIONEER authorized service center or your dealer to carry out repair work.

i.LINK indicator flashes, but no

sound is output.

• An output signal is not produced from

the i.LINK connector on the source

player.

• The selected component is not compati-

ble with i.LINK Audio.

• The selected component does not corre-

spond to DTCP.

• Refer to the manual that came with the

source player.

• Refer to the manual that came with the

source player.

• The unit corresponds to DTCP. Refer to

the manual for the selected compo-

nent.

i.LINK indicator does not light

up even when an i.LINK-

equipped component is

selected.

• The i.LINK cable is dislocated.

• The i.LINK cable is too long.

• The selected component does not corre-

spond to the i.LINK AUDIO format.

• The component between the unit and

the source player is turned off.

• Check all connections.

• Use a cable less than 3.5m long.

• Refer to the manual for the selected

component.

• When the source player is turned off or

in the standby mode, the output signal

is not produced. Refer to the manual

for the selected component.

The program format

indicators don’t disappear

when SACD/DVD-A playback

stops.

• The program format indicators remain lit

until another format source is input.

PQLS OFF or PQLS ON is

displayed temporarily and the

sound output is discontinued.

• During playback through an i.LINK con-

nection, if you change the settings for

other i.LINK components, the sound will

be discontinued momentarily.

After upgrading a component

and then connecting it

through an i.LINK connection,

the name for the component

is not displayed and the

component is not selected.

• Depending on the upgrade process, cer-

tain components may not be recognized

by the unit.

• Initialized all the information stored in

the unit in the order as follows:

1. When the unit is in the standby

mode, press and hold STEREO/DIRECT

and then press STANDBY/ON.

2. When “DB CLEAR?” is displayed,

press MULTI CH IN.

3. When “DB CLEAR OK?” is displayed,

press ACOUSTIC EQ.

4. Make sure “DB CLEAR SET” is

displayed to end initialization.

5. If “DB ERROR” is displayed, step

through the procedure again.

The power does not turn on • The power plug is disconnected.

• The protection circuit may have been

activated.

• Connect the power plug to the wall out-

let.

• Disconnect the power plug from the

outlet, and insert again.

Power

i.LINK interface

Cause

Remedy

Symptom

VSX-AX5i.book Page 109 Friday, May 23, 2003 6:33 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer VSX-AX5i-S Seite 109

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer VSX-AX5i-S

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info