Bedienungsanleitung Polar PROTRAINER XT (Seite 17 von 29) (Englisch)

542820

Zoom out

Zoom in

Vorherige Seite

1/29

Nächste Seite

32 33

There is a bike symbol in the time of day

display if your most recent exercise was done

in the Cycling mode.

1. Press SELECT to start the Cycling mode.

The receiver starts searching for coded

transmission for max. 20 seconds.

The coded heart rate information appears

in the bottom line of the display.

If the code search was not successful, 00

appears in the display. Restart the measurement

from the Time of day display and follow the above

mentioned precautions during the code search.

Swap the wheel size

If you have two bikes with different wheel sizes you should set

values for both the WHL 1 and WHL 2.

Calibrating the wheel size.

Swap the wheel size according to your bike as follows:

1. Start the cycling measurement but don't start the stopwatch yet.

2. Press and hold the SELECT button until the WHL 1 / WHL 2 is

displayed for a few seconds.

Display will return to the cycling measurement mode.

6. Start the stopwatch by pressing SET/START/STOP.

Stopwatch starts running and you hear a long beep.

Display is illuminated for a few seconds.

7. You can now start your cycling exercise.

Your safety is important to us. While riding your bike, please keep

your eyes on the road to prevent possible accidents and injury.

Display in the Cycling mode

• cycling info loop

Cycling info loop includes: trip, stopwatch,

time of day, average speed, maximum

speed and lap number. Select the cycling

info display by pressing SIGNAL/LIGHT.

• Target Zone indication

• speed

• cycling mode indicator

• heart rate

FUNCTIONS DURING THE

MEASUREMENT IN THE

CYCLING MODE

1. START THE CYCLING MEASUREMENT

1. Wear the Transmitter as described in Getting going.

2. Attach the Polar Protrainer XT receiver on the Polar Bike Mount.

3. Install the Polar Speed Sensor on the front fork of your bike as

instructed in the Polar Speed Sensor manual.

4. Check that there are no disturbances near you as you are about to start

the code search for coded transmission.

Make sure that the code search will be successful:

• Keep the bike still.

Do not ride or move your bike before

the code has been picked up.

• Keep the receiver within 3 feet/1 metre from your Polar

Coded Transmitter.

• Check that you are not near to other people with heart rate

monitors, high voltage power lines, televisions, mobile phones,

cars, exercise equipment etc.

5. There are two different ways to start the cycling measurement. Check

whether you have the cycling symbol in the Time of day display or not

and, according to that, start the code search and heart rate

measurement as follows:

There is no bike symbol in the time of

day display if your most recent exercise

was done in the Heart rate mode.

1. Press SET/START/STOP and

SIGNAL/LIGHT simultaneously in

the Time of day display to start

the Cycling measurement.

PROXT GBR/E 7.2.2001, 09:0132-33

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Polar PROTRAINER XT Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info