Bedienungsanleitung Polar RCX 3 (Seite 49 von 57) (Englisch)

520075

Zoom out

Zoom in

Vorherige Seite

1/57

Nächste Seite

Prior to changing the battery, please note the following:

• The low battery indicator is displayed when 10-15% of the battery capacity is left.

• Before battery change, transfer all data from your RCX3 to polarpersonaltrainer.com to avoid data loss. For

more information, see Data Transfer (page 27).

• Excessive use of the backlight drains the battery more rapidly.

• In cold conditions, the low battery indicator may appear, but will disappear when the temperature rises.

• The backlight and sound are automatically turned off when the low battery indicator is displayed. Any

alarms set prior to the appearance of the low battery indicator will remain active.

Keep the batteries away from children. If swallowed, contact a doctor immediately. Batteries should be disposed of

properly according to local regulations.

Change Batteries Yourself

To change the batteries of the training computer and heart rate sensor yourself, carefully follow the

instructions below:

When changing the battery, make sure the sealing ring is not damaged, in which case you should replace

it with a new one. You can purchase the sealing ring/battery kits at well-equipped Polar retailers and

authorized Polar Services. In the USA and Canada, the additional sealing rings are available at authorized

Polar Service Centers. In the USA the sealing ring/battery kits are also available at www.shoppolar.com.

When handling a new, fully charged battery, avoid clasp-like contact, i.e. simultaneously from both sides,

with metal or electrically conducting tools, like tweezers. This may short circuit the battery, causing it to

discharge more rapidly. Typically, short circuiting does not damage the battery, but it may decrease the

capacity and the lifetime of the battery.

Changing Training Computer Battery

1. Use the battery cap tool to open the battery

cover. Position the tool so that it fits in correctly

on the top of the back cover and turn it from

CLOSE to OPEN. Remove the battery cover.

2. Lift the battery out carefully. Be careful not to

damage the metal sound element or the grooves.

Insert a new battery with the positive (+) side

outwards.

3. Close the cover with the battery cap tool and

re-enter the basic settings.

Changing Polar H1/H2/H3 Heart Rate Sensor

Battery

1. Lever the battery cover open by using the clip on

the strap.

2. Remove the old battery from the battery cover

with a suitable sized small ridgid stick or bar,

such as a toothpick. A non-metal tool is

preferable. Be careful not to damage the battery

cover.

3. Insert the battery inside the cover with the

negative (-) side outwards. Make sure the sealing

ring is in the groove to ensure water resistance.

4. Align the ledge on the battery cover with the slot

on the connector and press the battery cover

back into place. You should hear a snap.

ENGLISH

Important Information 49

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Polar RCX 3 Seite 49

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Polar RCX 3

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info