Bedienungsanleitung Polar RCX 3 (Seite 50 von 57) (Englisch)

520075

Zoom out

Zoom in

Vorherige Seite

1/57

Nächste Seite

Changing Polar WearLink+ Heart Rate Sensor

Battery

1. Using a coin, open the battery cover by turning it

counterclockwise to OPEN.

2. Insert the battery inside the cover with the

negative (-) side outwards. Make sure the sealing

ring is in the groove to ensure water resistance.

3. Press the cover back into the connector.

4. Use the coin to turn the cover clockwise to

CLOSE.

Danger of explosion if the battery is replaced with wrong type.

Power Save Mode

The power save mode is enabled by default.

During the night, in between the hours 24:00 - 06:00 / 12:00am - 06:00am, the training computer

display will be switched off automatically. During this time the AutoSync function is not enabled. To exit

the power save mode, press any button. After five minutes, the display returns to power save mode.

The power save mode will not be enabled during training session recording.

The time period during which the power save mode is enabled, can be modified in the WebSync software,

to better suit your training schedule. For more information, see WebSync Help.

Battery Lifetime in RCX3

The battery lifetime for the RCX3 training computer is on average 7-8 months and depends on which

features and sensors you use. The suggestions below will help you to lengthen the battery lifetime.

To get the 8 months lifetime for the battery, take the following settings into use in your training computer:

• Set the AutoSync off in MENU > Connect > AutoSync > Off.

• Set the GPS sensor off in MENU > Settings > Sport profiles, when you do not need speed, distance or

location data.

Precautions

The Polar training computer shows your performance indicators. Polar training computer is designed to

indicate the level of physiological strain and recovery during and after exercise session. It measures heart

rate, speed and distance when cycling with a Polar CS speed sensor W.I.N.D. It also measures speed and

distance when running with a Polar s3+ stride sensor or with a Polar G5 GPS sensor / Polar G3 GPS sensor

W.I.N.D.. The Polar CS cadence sensor W.I.N.D. is designed to measure cadence when cycling. No other

use is intended or implied.

The Polar training computer should not be used for obtaining environmental measurements that require

professional or industrial precision.

Interference During Training

Electromagnetic Interference and Training Equipment

Disturbance may occur near electrical devices. Also WLAN base stations may cause interference when

training with the training computer. To avoid erratic reading or misbehavior, move away from possible

sources of disturbance.

Training equipment with electronic or electrical components such as LED displays, motors and electrical

brakes may cause interfering stray signals. To solve these problems, try the following:

ENGLISH

50 Important Information

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Polar RCX 3 Seite 50

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Polar RCX 3

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info