Bedienungsanleitung Polaroid 600 autofocus (Seite 10 von 19) (Englisch)

294948

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

600/600 SE Camera User Guide

Coat black and white prints: Prints from all

black and white films except Type 667 must

be coated as soon as possible to protect

them from scratches, fingerprints and fading,

and to prevent changes in tone. For details,

see the film instructions. Do not coat color

prints.

Type 665 negatives: These must be

immersed in a sodium sulfite solution

immediately after separation from the

positive print. See the instructions on the

inside of the fim box for full details.

Protect film from heat: Keep film away

from heat. Extreme heat and humidity can

damage it, especially after the pack is

removed from its sealed foil wrapping.

Troubleshooting

If no white tab appears: Open the door

and, without moving the film pack, push the

white tab out (49). Then close and latch the

door.

If no yellow tab appears when you pull

the white tab: Do not pull another white tab.

Instead, carefully open the holder far enough

to get a finger on top of the film pack to hold it

down (50). Grasp the topmost yellow tab,

and gently pull it all the way out and discard it

(51). Inspect the rollers and clean them if

necessary. Close and latch the holder, with

the next white tab sticking out.

Picture faults and probable

causes

Repeated, evenly-spaced spots: Due to

dirt on the steel rollers in the film holder.

Missing corners or orange-red marks

along edges: Caused by pulling the yellow

tab out of the camera at an angle. Also

caused by dried developer chemicals at the

ends of the steel rollers in the film holder.

Oblong in print: The white tab was not

pulled all the way out. When the yellow tab

was pulled, the white tab was pulled back into

the camera.

Many small white specks: Caused by

pulling the yellow tab out too fast. This can

also cause pink lines, streaks or blotches on

color prints.

Picture with dull, weak colors: The print

was not developed long enough.

Underdeveloped color prints may be

brownish pink.

Picture with reddish tint and muddy

colors: The picture was developed at

temperatures below 65

F (18

C).

Color prints much too red: May occur with

some electronic flash units when set at

“Auto”.

Very light image or none at all: The film

was fogged or extremely overexposed. Do

not remove the safety cover from the film

pack before inserting it into the camera, and

do not remove a loaded film holder from the

camera without inserting the dark slide. Be

sure your exposure is based on the correct

film speed.

Nearly black image or solid black:

Caused by insufficient or no exposure. Be

sure you have cocked the shutter and

removed the dark slide. Be sure your

exposure is based on the correct film speed.

Broad streak or curtain-shaped mark:

Due to hesitation or stopping while pulling the

yellow tab out.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Polaroid 600 autofocus Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info