| 4 | www.polisport.com
For child saf
perfect child carr
bicycles.
Our ergonomic child seats are all built with saf
primary goals.
In this manual, you will find information on attaching the child bicycle seat
to the frame of your bicycle.
Carefully read the manual f
bicycle seat.
REAR CHILD-SEA
FRAME MOUNTING SYSTEM
EN
•
shock absorbers.
•
drop handlebar
•
as Mopeds and Scooters.
•
square or carbon fiber frames.
•
oval frames with diameters ranging fr
•
diameters of 26”
•
maximum weight of 22 Kg (and children with r
from 9 months to 5 years of age - with the w
•
the maximum permitted load permitted for the bicycle. Information on
the maximum load can be found in the operating instructions of the
bicycle.
•
of such additional loads.
•
rider does not touch the child bicycle seat with the feet when in motion.
• It’s very important to adjust correctly the seat and its component parts
for optimum comfort and safety of the child. It’s also important that the
seat does not slope forward, so that the child does not tend to slide out of
it. It’s also important that the backrest slope backward slightly
• Check if all parts of the bic
seat mounted.
• Check the instructions of the bicycle, and If you have an
on fitting the child bicycle seat to your bicycle, please contact your
bicycle supplier for further information.
TECHNICAL FEA
1.
metallic bracket (H) from the seat by cutting the straps
2. Unscrew the hand knob (J2) and simultaneously lift the red security
ring (J3).
3.
it according to the dir
4. Hold the metallic bracket (H) the same as in the picture and pass it
through the opening in the child bicycle seat.
5. In order to adjust the child bicycle seat according t
the metallic bracket (H) into one of the three allow
the seat backward or forward. At the beggining w
the position No. 3.
6. Insert the metallic mounting plate (J1) on the grooves of the child
bicycle seat, and close it as indicated in the picture.
7. Close the metallic mounting plate (J1); make sure it holds the metallic
bracket (H) and fasten the hand knob (J2). As soon as the hand knob is
well tightened, make sur
the picture.
8. Remove the screws (I1) on the mounting block (I), with the Allen key
no. 5 (I5).
9. Before placing the block onto the frame
rubber (I7) is correctly positioned on front of the block.
10. Place the main body of the mounting block (I2) on the front of the
bicycle frame, and then place the metallic mounting plate (I4).
Note: If they are cables in this area make sur
positioned in the central groov
protective rubber (I7) and the gr
able to move freely).
11. Place the washer (I6) in the M6 screws (I1), and then screw them
on to the mounting block (I).
that the mounting block (I) is secured but not fully tightened so that
necessary, you can adjust the height later
be tight to make it easier to complete the next stepY
the 4 screws diagonally and in stages. Check the safety of the fasteners
regularly
12. Place the edges of the metallic bracket (H) at the holes of the metallic
bracket (I) until you hear a click indicating the lock, and until the center
button (I3) shall be level with the exterior of the hose metallic bracket.
13. Centre and adjust the metallic bracket (H) at a heigh
rear wheel, so that lat
child bicycle seat does not touch the wheel. Note that the metallic
bracket (H) should be positioned at a maximum of 10 cm away fr
the wheel.
child seat) that must be positioned in front of the r
is positioned behind the axle, the distance must not exceed 10 cm.
If the center of gravity is at a upper distance from the axle
metal bracket to one of the available positions. Special car
taken when positioning the child seat to ensure that the cyclist does not
touch the child seat with his feet when cycling.
Note: In Germany, acc
seats may only be fixed so that 2/3 of the seat depth or the Gra
of the seat is located between the front and r
14. After adjusting the height and positioning of the seat, hand tighten
the mounting block (I) to ensure that it cannot mov
be manual and is extremely important for the safety of the child. Make
sure that the mounting block (I) is firmly attached.
the 4 screws diagonally
15. Pass the saf
in the picture, under tension. Make sure that r
contact with the wheel.
safety.
16.
sliding the adjusters (B2).
ASSEMBL
A. Main seat
B. Safety belt
B1.
B2.
B3.
B4.
C. Safety belt for bic
D. Footrest strap
E. Footrest
E1.
F. Centre of Gravity
G. Cushion
H. Metallic bracket
I. Mounting block
I1. Screws M6x45
I2. Plastic mounting block
I3. Release button
I4. Metallic mounting plate
I5. Allen key no. 5
I6. Lock washer M6
I7. Protective rubber
J. Metallic mounting Kit
J1. M
J2. Hand k
J3. Safet
K. Batch serial number
T
