773024

Polisport Guppy junior plus Seite 6

6
Zoom out
Zoom in
Vorherige Seite
1/70
Nächste Seite
| 4 | www.polisport.com
1. Turn over the seat as shown in the picture.
2. Unscrew the hand knob (G1) and simultaneously lift the red security
ring (G2). Open the jaw (G3) to an aperture wider than the luggage carrier.
3. Place the seat on the luggage carrier and then fasten the hand knob
(G1) so that the seat remains slightly attached to the luggage carrier.
Check if the jaw (G3) is properly fastened to the luggage carrier.
4. The child seat has a centre of gravity (F) (inscribed on the child seat) that
must be positioned in front of the rear wheel axle. If it is positioned behind
the axle, the distance must not exceed 10 cm. If the centre of gravity is
more than this distance from the axle, adjust the seat to the correct
position. Special care must also be taken when positioning the child seat
to ensure that the cyclist does not touch the child seat with his feet when
cycling. Make sure that the mounting plate (G) is firmly attached to the
carrier before proceeding. This step is extremely important for child and
cyclist safety. Check the safety of the fasteners regularly.
Note: In Germany, according to the German Traffic Law StVZO, bicycle
seats may only be fixed so that 2/3 of the seat depth or the Gravity Center
of the seat is located between the front and rear axle of the bicycle.
5. Fasten the hand knob (G1) so that the seat is well attached to the
luggage carrier. As soon as the hand knob is well tightened, make sure the
security lever is properly held as shown in the picture.
6. Pass the safety belt (C) around the bicycle frame. Adjust it as shown
in the picture, under tension. Make sure that remain loosen belt is not in
contact with the wheel. This step is extremely important for the child’s
safety.
7. The Guppy Junior seat must always be used with wheel protectors (D3).
They are strictly mandatory as it stops your child’s foot from coming into
contact with the wheel and prevent accidents. Place the protective film
for the fork (E5) to cover the location where the metal plate will be applied
(E1). Polisport provides this film for the protection of the fork and is not
responsible for any damage to the forks.
8. Fit metal attachment plate Ø[17-21]mm (E1) on the rear wheel’s right
hand fork. Repeat the same process for the left hand side.
9. Place the zip ties (D4) in the wheel protector (D3) as shown in the
picture. Is mandatory to install the 6 zip ties on each wheel protector.
10. Start to attach the zip ties (D4) to the bicycle fork. The zip tie located
on the bottom should be attached after the metal attachment plate (E1).
11. Attach the other 3 zip ties to the wheel bar by choosing the holes
that better fit to your bicycle wheel size. Follow the picture instructions
for the guidance.
12. Cut the remaining tape and leave at least 4mm as shown in the
picture. Make sure you have followed all the previous steps before you
go to the next instruction. Test your bicycle wheel to make sure your
wheel turn around with no issue. Repeat this process on both sides of the
bicycle. Make sure you have both wheel protectors installed as described
in the instruction. You’re now ready to go to the next step to install the
retractable footrest.
13. Please do not proceed with this step before you follow the previous
steps to install the wheel protector. This is important for you and your child
security. Fit the fastening block (E2) to the metal attachment plate (E1)
After putting this component in place, ensure that its attachment pins
fit properly into the metal attachment plate (E1), as shown on the above
image. Repeat the same process for the left hand side. Polisport does not
accept liability for any damage caused to the fork if this part is tightened
incorrectly.
14. Fit the retractable footrest (D2) onto the plate and block assembly
(E2+E1) installed previously to the rear wheel’s right hand fork. Repeat the
same process for the left hand side.
15. After fitting the retractable footrest (D2), insert the M6 bolt into the
top slot and tighten the footrest (D2) onto the block installed on the rear
wheel’s right hand fork in the previous steps. After inserting the 2 bolts,
use the no. 4 Allen key (E4), to tighten them (6N.m) to ensure that they
do not come loose with daily use. Repeat the same process for the left
hand side.
• This junior bicycle seat must not be mounted to bicycles fitted with rear
shock absorbers.
• This junior bicycle seat must not be mounted to Motorized Vehicles such
as Mopeds and Scooters.
• This junior bicycle seat must be assembled on a carrier with at least 38kg
/ 83.78 Lbs of capacity.
• For safety reasons this seat shall only be fitted to luggage carriers in
accordance with ISO 11243 - 120 to 175 mm. Also fitting wider carriers
- 185mm.
• This junior bicycle seat must be assembled on bicycles with wheels with
diameters of 26”, 27.5”, 28” and 29”.
• This junior bicycle seat is only suitable for carrying children with a
maximum weight of 35 Kg, minimum height of 1,10mts and above 6 years
of age, that are able to secure and keep their balance autonomously on
the seat during the ride.
• The total weight of the cyclist and the child transported must not exceed
the maximum permitted load permitted for the bicycle. Information on
the maximum load can be found in the operating instructions of the
bicycle. You can also contact the manufacturer for this question.
• The seat may only be mounted on a bicycle suitable for the attachment
of such additional loads.
• The position of the junior bicycle seat must be adjusted so that the
bicycle rider does not touch the child bicycle seat with the feet when in
motion.
• It’s very important to adjust correctly the seat and its component parts
for optimum comfort and safety of the child. It’s also important that the
seat does not slope forward, so that the child does not tend to slide out of
it. It’s also important that the backrest slope backward slightly.
• Check if all parts of the bicycle function correctly with the junior bicycle
seat mounted.
• Check the instructions of the bicycle, and If you have any doubts
on fitting the junior bicycle seat to your bicycle, please contact your
bicycle supplier for further information.
ASSEMBLY INSTRUCTIONS
TECHNICAL FEATURES
A. Main seat
B. Safety belt
B1. Safety lock
B2. Belt adjuster
C. Safety belt for bicycle frame
D. Foot protector and footrest
assembly
D1. Foot protector
D2. Retractable footrest
D3. Wheel protector
D4. Zip ties (12)
E. Assembly kit for foot
protector and footrest (D2)
E1.
Metal attachment plate Ø[17-21]mm
E2. Fastening block
E3. Bolts M6
E4. No. 4 Allen key
E5. Protective film for the fork
F. Centre of Gravity
G. Mounting plate to luggage
carrier
G1. Hand knob
G2. Safety red ring
G3. Jaw
H. Cushion
I. Batch serial number
TABLE OF CONTENTS OF PRODUCT
For child safety and for your peace of mind, Polisport has developed the
perfect child carrying solution that’s suitable for a wide range of adult
bicycles.
Our ergonomic junior seats are all built with safety and comfort as the
primary goals.
In this manual, you will find the information to attach the junior seat to
the carrier.
Carefully read the manual for a safe and correct installation of the
junior bicycle seat.
REAR JUNIOR SEAT FOR BICYCLE
CARRIER MOUNTING SYSTEM
EN
… 6 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Polisport Guppy junior plus wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info