| 4 | www.polisport.com
1. Remove the mounting block (I) from the metallic bracket (H).
you should press the metallic bracket button (I3) and simultaneously pull
the metallic bracket (H) up.
2. Use the Allen key No. (I5) to loosen and r
plate (J1).
3. Hold the metallic bracket (H) the same as in the picture and pass it
through the opening in the child bicycle seat.
4. In order to adjust the child bicycle seat according t
the metallic bracket (H) into one of the three allow
the seat backward or forward. At the beginning w
the position No. 3.
5. Insert the metallic mounting plate (J1) on the grooves of the child
bicycle seat, and close it as indicated in the picture.
6. Place the washer (J3) on the screw (J2). T
key (I5).
This step is extremely important for the safety of the child.
7. Remove the screws (I1) on the mounting block (I), with the Allen key
no. 5 (I5).
8. Before placing the block onto the frame
rubber (I8) is correctly positioned on front of the block.
9. Place the main body of the mounting block (I2) on the front of the
bicycle frame, and then place the metallic mounting plate (I4).
Note: If they are cables in this area make sur
positioned in the central groov
protective rubber (I8) and the gr
able to move freely).
10. Place the washer (I6) in the M8 screws (I1), and then screw them
on to the mounting block (I).
that the mounting block (I) is secured but not fully tightened so that
necessary, you can adjust the height later
be tight to make it easier to complete the next stepY
the 4 screws diagonally and in stages. Check the safety of the fasteners
regularly
11. Place the edges of the metallic bracket (H) at the holes of the
mounting block (I) until you hear a click indicating the lock, and until the 2
green safety device indicators pop up on the fr
The child bicycle seat will only be properly installed when the 2 green
safety device indicators are visible.
child’
12. Centre and adjust the metallic bracket (H) at a heigh
rear wheel, so that lat
child bicycle seat does not touch the wheel. Note that the metallic
bracket (H) should be positioned at a maximum of 10 cm away fr
the wheel.
child seat) that must be positioned in front of the r
is positioned behind the axle, the distance must not exceed 10 cm.
If the center of gravity is at a upper distance from the axle
metal bracket to one of the available positions. Special car
taken when positioning the child seat to ensure that the cyclist does not
touch the child seat with his feet when cycling.
Note: In Germany, acc
seats may only be fixed so that 2/3 of the seat depth or the Gra
of the seat is located between the front and r
13. After adjusting the height and positioning of the seat, hand tighten
the mounting block (I) to ensure that it cannot mov
be manual and is extremely important for the safety of the child. Make
sure that the mounting block (I) is firmly attached.
the 4 screws diagonally
14. Pass the saf
in the picture, under tension. Make sure that r
contact with the wheel.
15.
sliding the adjusters (B2).
T
press the three buttons of the lock (B1) as indica
For child saf
perfect child carr
bicycles.
Our ergonomic child seats are all built with saf
primary goals.
In this manual, you will find information on attaching the child bicycle seat
to the frame of your bicycle.
Carefully read the manual f
bicycle seat.
•
shock absorbers.
•
drop handlebar
•
as Mopeds and Scooters.
•
square or carbon fiber frames.
•
oval frames with diameters ranging fr
•
diameters of 26”
•
maximum weight of 22 Kg (and children with r
from 9 months to 5 years of age - with the w
•
the maximum permitted load permitted for the bicycle. Information on
the maximum load can be found in the operating instructions of the
bicycle.
•
of such additional loads.
•
rider does not touch the child bicycle seat with the feet when in motion.
• It’s very important to adjust correctly the seat and its component parts
for optimum comfort and safety of the child. It’s also important that the
seat does not slope forward, so that the child does not tend to slide out of
it. It’s also important that the backrest slope backward slightly
• Check if all parts of the bic
seat mounted.
• Check the instructions of the bicycle, and If you have any doubts
on fitting the child bicycle seat to your bicycle, please contact your
bicycle supplier for further information.
ASSEMBL
RECLINING CHILD SEA
TECHNICAL FEA
A. Main seat
B. Safety belt
B1.
B2.
B3.
B4.
C. Safety belt for bicycle frame
D. Footr
E. Footrest
F. Centre of Gra
G. Cushion
H. Metallic bracket
I. Mounting block
I1. Screws M8x45
I2. Plastic mounting block
I3. Release button
I4. Metallic mounting plate
I5. Allen key no. 5
I6. Lock washer M8
I7. Safety device indicator
I8. Protective rubber
J. M
J1. Metallic mounting plate
J2. M8x25 screw
J3. M8 washer
K. Batch serial number
L.
Mechanism for reclining the s
L1. Safety lever
L2. Lever t
M. T
T
FRAME MOUNTING SYSTEM
EN
