Bedienungsanleitung Polti LECOLOGICO AS 806 (Seite 9 von 10) (Englisch)

649056

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

LECOLOGICO AS 805 - AS 806 SPECIAL PETS

• Remove the sponge filter (17b) from the cage.

If the filter is damaged, replace it. Rinse all com-

ponents under running water. Let the sponge fil-

ter dry before putting it back into the appliance.

• Reassemble the filter assembly, repeating the

operations in the reverse order.

Note: Make sure that the filter nozzle (17c) is cor-

rectly positioned, checking that the arrow on the

nozzle is aligned with the notch on the bottom of

the cage (17a) (fig.15).

• If the filter needs replacing, always use an origi-

nal Polti filter, available by mail order from the

Technical Service Centre.

•A cleaning brush (Z) is supplied for easy clean-

ing of the water container (6); it may also be

used to clean the appliance’s hose connections

and the inside of tools.

NOTE: Do not use the brush for cleaning the out-

side of the appliance

((

))

““

””

((

))

Proceed as follows to clean filters:

•press the two levers on the filter cover (9a) and

pull off the filter cover (9) (fig.16).

• Pull on the “dual filter” (10b) to remove it from

its housing and then remove the microfilter and

moisture protection filter that compose it

(fig.19).

• Rotate the filter retainer (10a) as shown in

fig.17 and remove the Hepa filter (10) (fig.18).

• Rinse the filters in cold running water. Shake

them gently after washing to eliminate any resid-

ual dirt and excess water.

• When dry, put the filters back in the appliance,

performing the same operations in reverse or-

der.

NOTE: let the filters dry naturally, far away from

light and heat sources. You should wait 24 hours

before reassembling filters in the appliance.

• Replace the filters if they are torn.

• Filters should be cleaned every 4 months.

WARNING: do not clean filters with the brush, as

this could damage them, decreasing their filtering

capacity.

Do not use detergents, do not scrape filters, and

do not attempt to wash them in a dishwasher.

• The vacuum cleaner won’t start:

check that the appliance is plugged in

• The vacuum cleaner goes off during use

and the four indicator lights come on:

a) there is too much liquid in the container. Re-

store the correct level.

b) The selected power level is too high for the

type of surface you are cleaning.

In both cases, press the switch (1), unplug the

power cable and leave it unplugged for a few

seconds so that the safety device will be re-

set.

• Suction power is decreased:

The nozzle, hose or tools may be blocked up, or

the Hepa filter may be dirty. Clean the Hepa fil-

ter and remove any obstructions from the hose.

• Leakage of water when suctioning up liq-

uids:

The float may be blocked up. Clean the filter as-

sembly and make sure that the water level in the

container is correct.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Polti LECOLOGICO AS 806 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Polti LECOLOGICO AS 806

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info