Bedienungsanleitung Powerplus pow xq5104 (Seite 6 von 12) (Englisch)

391294

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

POWXQ5104 EN

6 SPECIFIC SAFETY INSTRUCTIONS FOR ANGLE GRINDERS

 Check that the maximum speed indicated on the grinding disc corresponds to the

maximum speed of the machine. The speed of the machine must not exceed the value on

the grinding disc.

 Make sure that the dimensions of the grinding disc correspond to the specifications of the

machine.

 Make sure that the grinding disc has been mounted and fastened properly. Do not use

reducing rings or adapters to make the grinding disc fit properly.

 Treat and store grinding discs in conformance with the supplier’s instructions.

 Do not use the machine for grinding workpieces with a maximum thickness exceeding the

maximum grinding depth of the grinding disc.

 Do not use cutting discs for deburring.

 When grinding discs have to be mounted on the thread of the spindle, make sure that the

spindle has sufficient thread. Make sure that the spindle is sufficiently protected and does

not touch the grinding surface.

 Before use, inspect the grinding disc for any damage. Do not use grinding discs which are

cracked, ripped or otherwise damaged.

 Before use, let the machine run idle for 30 seconds.

 Immediately switch off the machine in case of abnormal vibrations or occurrence of

another defect. Carefully inspect the machine and grinding disc before switching the

machine on again.

 Make sure that sparks do not put people into danger or that they contact highly flammable

substances.

 Make sure that the workpiece is sufficiently supported or clamped. Keep your hands away

from the surface to be cut.

 Always wear safety goggles and hearing protection. If desired or required also use another

kind of protection, like for example an apron or helmet.

 Ensure that mounted wheels and points are fitted in accordance with the manufacturer’s

instructions.

 Ensure that blotters are used when they are provided with the bonded abrasive product

and when they are required.

 If a guard is supplied with the tool never use the tool without such a guard.

 For tools intended to be fitted with threaded hole wheel, ensure that the thread in the

wheel is long enough to accept the spindle length.

 Ensure that ventilation openings are kept clear when working in dusty conditions. If it

should become necessary to clear dust, first disconnect the tool from the mains supply

(use non metallic objects) and avoid damaging internal parts.

 Though poor conditions of the electrical mains, shortly voltage drops can appear when

starting the equipment. This can influence other equipment (eq. blinking of a lamp). If the

mains-impedance Zmax <0.348 Ohm, such disturbances are not expected. (In case of

need, you may contact your local supply authority for further information.

7 ASSEMBLY / MOUNTING ACCESSORIES

Prior to mounting/dismounting an accessory always unplug the tool.

7.1 Mounting / adjusting / removing the guard

The safety guard of your POWXQ angle grinder is equipped with a quick clamp system,

allowing you to mount, move or remove the guard without tools.

Warning: Never operate the angle grinder without the safety guard properly

mounted and locked.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus pow xq5104 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus pow xq5104

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info