Bedienungsanleitung Powerplus pow xq5104 (Seite 7 von 12) (Englisch)

391294

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

POWXQ5104 EN

7.1.1 Mounting/installing the guard. (Fig 1)

 Make sure the quick clamp is in its open position.

 Position the guard on the guard basis. Please notice the notch on the inside of the guard

ring coincides with the foreseen cut out in the guard basis.

 Turn the guard in the desired position and tighten it by locking the clamp. (if the clamp is

not tight enough, open it again, tighten the nut using a spanner, then lock the clamp again)

7.1.2 Repositioning (turn) / removing the guard

 To reposition/turn the guard, release the quick clamp, turn the guard, and retighten the

clamp.

 To remove the guard: if installed, first remove the mounted disc, then work in the opposite

as described above under mounting/installing the guard.

7.2 Installing / replacing the grinding wheel (fig 2)

Prior to mounting/dismounting an accessory always unplug the tool.

Only Use discs of the correct dimension and of good quality. (Use fiber-reinforced

cutting/grinding discs (for stone-metal) or diamond disc (for stone) only).

The grinding disc may not touch the edge of the guard.

 Press the spindle lock (fig A, n° 5) and turn the spindle until it engages in the lock. Keep

the spindle lock pressed during this procedure.

 Loosen and remove the flange nut from the spindle using the spanner.

 Position the disc on the flange.

 Place the flange nut on the spindle and tighten using the spanner.

 Release the spindle lock and check that the spindle is unlocked by rotating it.

 Make sure the disc is installed in the correct way (direction of rotation)

Important! Never press the spindle lock before the motor and disc have come

to a complete standstill!

Never use the spindle lock to stop the motor. It will break.

For grinding/cutting discs up to approx. 3 mm thick, screw on the flange nut with the flat side

facing the grinding or cutting wheel. (Fig 3)

 Inspect discs regularly. Worn discs have a negative effect on efficiency of the machine

and may cause severe injury to user or damage to surrounding. Replace the grinding disc

on time.

7.2.1 Test run for new grinding wheels

When starting the tool, hold the tool in a well protected area and allow the angle grinder to

reach idle speed with the grinding/cutting disc fitted in place. Vibrating wheels are to be

replaced immediately.

7.3 Carbon brushes (fig 4)

Carbon brushes that are burned, broken or shorter than 5 mm are to be replaced by original

replacement brushes. Always replace the carbon brushes in pairs.

Your POWXQ angle grinder allows easy access to the cole brush. Remove the external brush

caps on either side of the machine using a Phillips (cross) screw driver

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus pow xq5104 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus pow xq5104

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info