Bedienungsanleitung Powerplus POW64256 (Seite 7 von 14) (Englisch)

480905

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

POW64256 EN

 Before commencing work, always check that the chainsaw works properly and is safe to

operate.

 Check also that the chain lubrication and the oil gauge are in good working order (see

Fig.4). When the oil lever is approx. 5 mm from the bottom mark, you must top up with oil.

When the oil level is higher you can work without worry.

 Switch on the chain saw and hold it above the ground. Be careful not allow the chainsaw

to touch the ground. For safety reasons it is best to keep a clearance of at least 20 cm. If

you now see growing traces of oil, the chain lubrication system is working correctly. If

there are no traces of oil at all, try cleaning the oil outlet (Fig 2, C), the upper chain

tensioning borehole (E) and the oil duct, or contact your Customer Service. (Be sure to

read the section “Filling in chain oil and chain lubrication” on this point).

 Check the chain tension and retention, if necessary (see the section “Tensioning the saw

chain” on this point).

 Make sure the chain brake is working properly (see also the section “Releasing the chain

brake”).

9 ASSEMBLY

9.1 Fitting the guide bar and chain (Fig 1, 2, 3)

If the chain saw is already connected to the power supply: Pull the plug

from the socket outlet. Wear protective gloves whenever doing any work on

the saw chain.

Important: The front finger guard (3) must always be in the top (vertical) position (Fig. 5).

The guide bar and saw chain are supplied separately. To assemble, first unscrew the lock nut

(5) and remove the guide bar cover (6). The guide bolt (17) must be in the centre of the guide.

If necessary, adjust the chain tensioning with the chain wheel (16).

To prevent injury on the sharp cutting edges, always wear gloves when

assembling, tensioning and checking the chain.

Before assembling the guide bar with the saw chain, check the cutting direction of the teeth!

The running direction is marked with an arrow on the cover (6) (Fig 3, G). To determine the

direction of cut, it may be necessary to turn over the saw chain (4). Hold the guide bar (7)

vertically with the tip pointing upwards and put on the saw chain (4, beginning at the tip of the

bar.

Then assemble the guide bar with the saw chain as follows:

 Place the guide bar with the saw chain on the chain wheel (16) and guide bolt (17).

 Place the saw chain round the chain wheel (16) and make sure it is correctly mounted (see

Fig.1, A).

 Place the cover (6) on top and tighten gently with the lock nut (5). Now the saw chain has

to be correctly tensioned.

9.2 Tensioning the saw chain

Always pull the plug out of the power socket before doing any work on the

chainsaw!

Wear safety gloves!

Make sure the saw chain (4) is inside the guide groove of the guide bar (7) (Fig.1 a)!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POW64256 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POW64256

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info