Bedienungsanleitung Powerplus POW64256 (Seite 8 von 14) (Englisch)

480905

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

POW64256 EN

Turn the outer Knob clockwise until the saw chain is correctly tensioned, then rotate the inside

knob (5) to block the guide bar in that position.

While the inside knob is being tightened, the guide bar must then be pushed upwards.

Check the chain tension again (see Fig. 3). Do not tension the chain too tightly.

When cold, it should be possible to lift the chain in the middle of the guide bar approx. 5 mm.

Tighten the lock nut (5) securely.

When warm, the saw chain will expand and slacken and there is a danger of it jumping off the

rail altogether. Re-tension if necessary.

If the saw chain is re-tensioned when hot, it must be loosened again when the sawing work

has been completed. Otherwise, the contraction which takes place as the chain cools would

result in excessively high tension.

A new saw chain requires a running-in period of approx .5 minutes. Chain lubrication is very

important at this stage. After running in, check chain tension and re-tension if necessary.

9.3 Filling in chain oil (Fig 4)

To prevent dirt getting inside the tank, clean the oil tank cap (21) before opening. Check the

contents of the oil tank during sawing work by checking the oil gauge (15). Close the oil tank

cap tightly and wipe away any spills.

9.4 Securing the extension lead (Fig 6)

Only use extension leads suitable for outdoor use. The cross section of the cable (max. length

of extension cord: 75m) must be at least 1,5 mm². secure the chainsaw flex to the extension

lead by inserting the extension lead into the strain relief gap of the housing.

Extension leads longer than 30 m will reduce the performance of the chainsaw.

9.5 Chain lubrication

To prevent excessive wear, the saw chain and guide bar must be evenly lubricated during

operation.

Lubrication is automatic. Never work without chain lubrication. If the chain runs dry, the entire

cutting apparatus will quickly become severely damaged. It is therefore important to check

both chain lubrication and the oil gauge every use (Fig. 4).

Never use the saw when the oil level is below the “Min.” mark.

 Min.: When only approx. 5 mm of oil is visible at the lower rim of the oil gauge (15), you

must top up with oil.

 Max.: Top up with oil until the window is full.

9.6 Checking the automatic lubrication

Before commencing work, check the automatic chain lubrication and oil gauge. Switch on the

chain saw and hold it above the ground. Be careful not to allow the chain saw to touch the

ground. For safety reasons it is best to keep a clearance of at least 20 cm. If you now see

growing traces of oil, the chain lubrication system is working correctly. if there are no traces of

oil at all, try cleaning the oil outlet (Fig 2, C), the upper chain tensioning borehole (E) and the

oil duct, or contact your Customer Service.

9.7 Chain lubricants

The service life of saw chains and guide bars depends to a large extent on the quality of the

lubricant used. Old oil must not be used! Use only environment-friendly chain lubricant. Store

chain lubricant only in containers which comply with the regulations.

9.8 Guide bar

The guide bar (7) is subjected to especially severe wear and tear at the nose and the bottom.

To avoid one-sided wear and tear, turn the guide bar over every time when you sharpen the

chain.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POW64256 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POW64256

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info