Bedienungsanleitung Powerplus POW8135 (Seite 6 von 11) (Englisch)

481010

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

POW8135 EN

§ Do not use the power tool if the switch does not turn it on and off. Any power tool that

cannot be controlled with the switch is dangerous and must be repaired.

§ Disconnect the plug from the power source before making any adjustments, changing

accessories, or storing power tools. Such preventive safety measures reduce the risk of

starting the power tool accidentally.

§ Store idle power tools out of the reach of children and do not allow persons unfamiliar with

the power tool or these instructions to operate the power tool. Power tools are dangerous in

the hands of untrained users.

§ Maintain power tools. Check for misalignment or sticking of moving parts, breakage of parts

and any other condition that may affect the power tool’s operation. If damaged, have the

power tool repaired before use. Many accidents are caused by poorly maintained power

tools.

§ Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting

edges are less likely to stick and are easier to control.

§ Use the power tool, accessories and tool bits etc., in accordance with these instructions and

in the manner intended for the particular type of power tool, taking into account the working

conditions and the work to be performed. Use of the power tool for operations different from

intended could lead to a hazardous situation.

6.5 Service

§ Have your power tool serviced by a qualified repair person using only identical replacement

parts. This will ensure that the safety of the power tool is maintained.

7 ADDITIONAL SAFETY INSTRUCTIONS FOR LASERS

§ Warning! The laser beam potentially causes severe eye damage. Never look or stare

directly into the laser beam.

§ During use, do not point the laser beam at people, directly or indirectly through reflecting

surfaces.

§ This laser complies with class 2 according to EN 60825-1:2001. The unit includes no

servicing components. Do not open the housing for any reason. If the unit is damaged, have

the damage repaired by an authorized repair agent.

8 ADDITIONAL SAFETY INSTRUCTIONS FOR BATTERIES

§ When replacing batteries, always replace the complete set. Do not mix old batteries with

new ones.

§ Prevent removed batteries from short circuiting.

§ Do not store batteries where the temperature may rise above 50 °C, e.g. in a car which has

been parked in the sun.

§ Do not burn batteries.

§ Never attempt to open batteries.

§ In case of battery leakage, carefully remove the liquid using a cloth. Avoid skin or eye

contact. Do not swallow. In case of skin or eye contact, rinse abundantly for 10 minutes with

clean water and consult a physician.

9 ASSEMBLY

9.1 Setting up the saw (Fig. 1 / 3/12)

§ Insert the two workpiece support clips (13) in the mounts (21) provided on the side of the

tool and fasten them in place with thumb screws (22).

§ Insert the clamping device (19) into one of the two mounts (20) provided on the top of stop

rail and fasten in place with the thumb screw (33).

§ Screw the additional stability bar (32) to the back of the machine.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POW8135 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POW8135

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info