Bedienungsanleitung Powerplus POW8135 (Seite 8 von 11) (Englisch)

481010

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

POW8135 EN

9.7 Precision adjustment of the stop for 45° mitre cuts (Fig. 8/9)

§ Lower the machine head (4) and fix with the lock pin (16).

§ Fix the rotary table (8) in 0° position.

§ Undo the tightening screw (12) and use the handle (2) to tilt the machine head (4) to the left

until it coincides at 45°.

§ Place the 45° stop angle (A) between the saw blade (5) and the rotary table (8).

§ Slacken the counter nut (25) and adjust the setting screw (26) until the angle between the

saw (5) and the rotary table (8) equals exactly 45°.

9.8 Mitre cuts 0-45 and rotary table 0-45" (Fig. 10)

§ The POW8130 can be used to make mitre cuts on the left at an angle of 0°-45° relative to

the work top and 0°-45° relative to the stop rail.

§ Lift the machine head (4) to its top position.

§ Undo the rotary table (8) by slackening the locking handle (10) and pressing the latch (11).

§ Adjust the rotary table (8) by its handle (2) to the required angle (see also Section D).

§ Retighten the tightening screw (10) in order to secure the turntable in place.

§ Undo the tightening screw (12) and use the handle (2) to tilt the machine head (4) to the left

until it coincides with the required angle value (in this connection see also section E).

§ Screw the tightening screw (12) back down again.

10 DUST BAG (FIG. 2)

The saw is equipped with a bag (14) to collect sawdust and chips. You can pull off the

sawdust bag (14) to the rear by pressing together the two clips (27). To empty the bag, undo

the zip at the bottom.

11 REPLACING THE SAW BLADE (FIG. 5/11)

§ Pull out the power plug.

§ Swing up the machine head (4).

§ Unscrew the two bolts (27, 28) and flip the cover plate up together with the saw blade guard

(6).

§ Press the saw shaft lock (17) with one hand while holding the wrench (32) on the flange bolt

(25) with the other.

§ Firmly press on the saw shaft lock (17) and slowly rotate the flange bolt (25) in clockwise

direction. The saw shaft lock engages after no more than one rotation.

§ Now, using a little more force, slacken the flange bolt (25) in clockwise direction.

§ Turn the flange bolt (25) until it is completely removed.

§ Take the blade (5) off the inner flange and pull out downwards.

§ Mount the new saw blade in reverse order and fasten.

§ Important! The cutting bevel of the teeth, i.e. the

§ direction of rotation of the saw blade, has to conform with the direction of the arrow marked

on the housing.

§ Clean the saw blade flanges thoroughly before mounting the saw blade.

§ Reattach the movable blade guard (6) in reverse order.

§ Before using the saw again, check that the safety devices are in good working order.

§ Important: Every time that you change the saw blade, check to see that it spins freely in the

groove of the turntable in both perpendicular and 45° angle settings.

12 ASSISTANT FENCE FUNCTION (FIG 14)

§ When angle of blade is 90°, please fit on part (A)

§ When angle of blade is 45°, please loose screw (a) to remove part (A)

13 LASER FUNCTION (FIG. 12)

You can switch the laser ON and OFF with the switch (a).

The laser (35) directs a beam onto the work-piece.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POW8135 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POW8135

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info