Bedienungsanleitung Powerplus POW900 (Seite 6 von 11) (Englisch)

582175

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

POW900 EN

7 BEFORE EVERY USE

Attention! The cable hoist is designed only for domestic use! It is not

intended for professional applications. This device can be operated without

hazards only if you read this user manual and safety instructions and

closely follow all instructions.

Prior to start-up operation, please be sure to make some preparations:

 Make sure the voltage of your power network complies with the voltage listed on the data

plate and that the device is equipped with the correct power plug.

 Please make no-loading test before start-up operation at first, and please check:

 a, The flexibility of the operating switch (16) to insure the controlling of the hoisting and

lowering of the load hook (12).

 b, The flexibility of lift limit bracket (8) to make sure the cut-off of circuit.

 c. The flexibility of down limit bracket (9) to make sure the cut-off circuit when the steel

cable (7) is nearly used up.

 d, Any abnormal sounds when start-up operation.

 e, The steel cable (7) is possible damaged (split or bent), change the cable immediately.

 Please check the brake before operating after load.

 Please inspect the load hook (12) before operation is possible damaged or distortional,

replace it in time.

 Operation using a residual current protective device (Emergency Switch, 15) offers

additional protection.

 Please be sure to the enough lubricant on parts. Daub the lubricant on the load hook (12),

cable drum shaft, slow down box, and bearing every half a year.

 Please daub the lubricant on the nesting of cable drum shaft when replace the steel cable

(7) every time. Immediately replace the cable if damaged.

 Please perform any rework and maintenance tasks only if the power plug is disconnected.

 Please inspect the device for transportation damages. Immediately report any possible

damages to your seller.

8 INSTALLATION

 Install the cable hoist on a steel beam (Fig 2). Use only the enclosed installation brackets

(1) which can be attached to the top of the mounting casing (3) using the screws, washers

and spring lock washers. The steel beam must be able to withstand at least double the

rated weight of the machine. Contact a professional installer for best results.

 The steel beam must have the following dimension: 46 x 46 mm, a wall thickness of at

least 2.3 mm and a length of at least 450 mm (Fig 1).

 The steel beam must be securely anchored in a wall. The anchor must be installed

correspondingly sturdy in order to be able to withstand the load.

 Please be sure that the machine is installed level and not slanted.

 The remote control (14) must be easily accessible at all times and must therefore be

installed at a distance to the floor of between 0.8 m and 1.5 m (Fig 3).

 Insert the load hook (12) into the hook bracket (5) of the mounting casing (3) when using

the load hook with pulley (13).

 The electric pulley will be attached at the top. Attach the pulley with bearer frame on the

crossbar. The girder is then attached to the support columns. The support columns must

be, in accordance with the requirements of the customer, properly secured on the working

area. The support columns must be installed to be sturdy and stable. Also be able to

withstand a nominal load long-term.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POW900 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POW900

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info