Bedienungsanleitung Powerplus POW900 (Seite 8 von 11) (Englisch)

582175

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

POW900 EN

9.1 Intermittent rating

This machine is designed for operating type S3 20% - 10 min (periodic intermittent operation).

The relative duty cycle is 20%, which means that the device can be operated at rated load for

2.0 minutes during each operating cycle and must then be switched off for 8. 0 minutes to cool

off. The device can therefore be continuously used for a duration of 20% of the total operating

cycle of 10 minutes at rated load.

9.2 Overload (Only for POW901-POW902-POW903)

 The cable hoist is not suitable for continuous operation. The motor is protected from

overload and overheating by a temperature switch.

 If the permissible operating time is exceeded, the motor temperature will increase and the

temperature switch will shut the cable hoist off. The temperature switch will automatically

switch back on after a cooling phase.

 In case of a strain on the cable hoist with a lesser load, the operating time will increase

and the cooling time will decrease.

Attention! In case of direct exposure to sunlight, the temperature of the

casing will increase significantly, which will also decrease the permissible

operating time. It is therefore possible that the temperature switch will

switch off after a short time period and the cable hoist will shut down.

Please wait until the device is cooled off.

9.3 Operation with double cable (Fig 5)

 Loosen the nuts of the 3 screws located on the load hook with pulley (13) and remove the

cover plate located on the side. Place the steel cable (7) around the deviating shaft and

reattach the cover plate and nuts. Please be sure that the load hook with pulley (13) is

installed properly and that the nuts are securely tightened.

 Please insert the load hook (12) attached to the cable into the hook bracket (5) of the

mounting casing (3).

10 CLEANING AND MAINTENANCE

 Disconnect the power plug prior to performing any work on the device.

 Clean the device using a damp cloth and some liquid soap. Never use cleaning agents or

solvents, these could damage the device's plastic parts.

 Regularly inspect the total length of the steel cable (7) for damages as well as the

functionality of the limit bracket (Wind cable hoist until the stopper (10) activates the limit

bracket of the micro switch).

 If the steel cable (7) is damaged (split or bent, fig 6), a professional must replace it using

original replacement parts.

 During assembly of the cable, it is imperative to remember the stopper in order to ensure a

secure limit stop.

 Inspect the free movement of all mechanical components after the power plug has been

disconnected.

 Replace lost parts only with original parts.

 Return the device to your seller to ensure professional recycling.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POW900 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POW900

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info