Bedienungsanleitung Powerplus POWP6050 (Seite 5 von 9) (Englisch)

675214

Zoom out

Zoom in

Vorherige Seite

1/9

Nächste Seite

POWP6050 EN

 After changing the bit or making any adjustments, make sure the collet nut and any other

adjustment devices are securely tightened. Loose adjustment device can unexpectedly

shift, causing loss of control; loss-rotating components will be violently thrown.

 Never start the tool when the bit is engaged in the material. The bit cutting edge may grab

the material causing loss of control of the cutter.

 Always hold the tool with two hands during start-up. The reaction torque of the motor can

cause the tool to twist.

 The direction of feeding the bit into the material is very important and it relates to the

direction of bit rotation. When viewing the tool form the top, the bit rotates clockwise. Feed

direction of cutting must be counter-clockwise (Fig 12). NOTE: inside and outside cuts will

require different feed direction; refer to section on feeding the router. Feeding the tool in

the wrong direction causes the cutting edge of the bit to climb out of the work and pull the

tool in the direction of this feed.

 Never use dull or damaged bits. Sharp bits must be handled with care. Damaged bits can

snap during use. Dull bits require more force to push the tool, possibly causing the bit to

break.

 Never touch the bit during or immediately after the use. After use the bit is too hot to be

touched by bare hands.

 Never lay the tool down until the motor has come to a complete standstill. The spinning bit

can grab the surface and pull the tool out of your control.

 Never use bits that have a cutting diameter greater than the opening in the base.

WARNING: Some dust created by power sanding, sawing, grinding, drilling,

and other construction activities contains chemicals known to cause

cancer, birth defects or other reproductive harm. Some examples of these

chemicals are:

 Lead form lead-based paints,

 Crystalline silica form bricks and cement and other masonry products, and

 Arsenic and chromium form chemically treated lumber.

Your risk form these exposures vary, depending on how often you do this type of work. To

reduce you exposure to these chemicals: work in a well ventilated area, and work with

approved safety equipment, such as those dust masks that are specially designed to filter out

microscopic particles.

7 ASSEMBLY

7.1 Inserting and removing a cutter (Fig. 1)

7.1.1 Inserting a cutter

 Press and hold down the spindle lock button (5).

 Using the wrench to loosen the collet nut (6) a few turns, insert a collet and a cutter into

order.

 Tighten the collet nut and release the spindle lock button.

7.1.2 Removing a cutter

 Press and hold down the spindle lock button (5) and loosen the collet nut (6) completely.

 Remove the cutter.

 Fit a new suitable accessory and tighten the collet nut.

Note: Never tighten the collet nut without a cutter in the collet.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POWP6050 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POWP6050

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info