Bedienungsanleitung Powerplus POWP6050 (Seite 6 von 9) (Englisch)

675214

Zoom out

Zoom in

Vorherige Seite

1/9

Nächste Seite

POWP6050 EN

7.2 Depth adjustment (Fig. 2)

Locate the depth stop (4) on the left-hand side of the cutting machine. This continuously

adjustable stop is intended to limit the depth of the cut. Loosen it by turning it in anticlockwise

direction. To move the depth stop up or down to the desired depth according to the marker of

the scale label (3).

NOTE: Make sure the locking knob (10) is fixed firmly when operating this

machine.

7.3 Locking lever (13) for cutting machine body

When viewed from the front, the locking lever is located at the rear on the left-hand side. The

cutting machine body is spring-tensioned. Take care when releasing the locking lever. Grasp

both handles and brace yourself before releasing the lever. Press downwards to allow the

cutting machine body to move down. When you reduce the downward pressure, the springs

force the cutting machine body back up into its highest position.

The released position (a) or lock position (b) of locking lever as shown in Fig. 3.

CAUTION: The housing of the machine is under spring tension. When you

release the locking lever, it returns to its highest position.

7.4 Mounting and adjusting the parallel guide (Fig. 4)

 The parallel guide can be used for cutting parallel to the edge of the work-piece.

 Fit the guide rods (a) to the frame using the screws (b).

 Release the two lock knobs securing the parallel guide and push them in so that the guide

is at the desired distance from the cutter head.

 Tighten the two lock knobs.

 Press the guide securely against the edge of the work-piece and execute the cut.

CAUTION: Abnormal vibrations may be due to a blunt cutter head.

7.5 Fitting the centre point (Fig. 5)

The centre point is used for routing circles.

 Remove a guide rod (a) from the parallel guide.

 Mount the centre point (b) to the guide rod.

 Slide the guide rod in the router base plate and tighten the lock knobs.

 Position the tip of centre point at the centre of your circle.

 Press it slightly so that the tip is firmly in the wood. You can now cut the circle.

7.6 Dust extraction outlet (Fig. 6)

It is advised to use the dust extraction outlet. You can purchase a suitable

commercial vacuum cleaner or extract the dust via an extractor tube while

the cutting machine is in operation. The outlet must project out of the rear

of the machine. Two bolts and nuts are supplied to attach it.

 Hold the dust extraction outlet (14) in position and lay the cutting machine on its side.

 Push the screw through the hole of the template guide (a), dust extraction outlet (14) and

router’s base plate (8) and until it projects at the fastening point for the dust extraction

outlet.

 Tighten the screw with a suitable screwdriver and moderate force until the outlet is

securely attached.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POWP6050 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POWP6050

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info