Bedienungsanleitung Powerplus POWX0026LI (Seite 9 von 12) (Englisch)

676177

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

POWX0026LI EN

The torque force is set by means of a torque setting according to the size of screw and the

kind of material. Select the suitable torque for the job to be performed. Long screws and/or

hard material require a higher torque setting.

8.6 Speed selector (Fig. 7)

NOTE： the L-mark is the “Low speed” position, the H-mark is the “High speed” position

(marks moulded in the button of two speed selector (3).)

The drill has a two-speed gear box designed for drilling at L (LOW) or H (HIGH) speed. The

gear selector is located on top of the drill to select either low or high speed. When you push

the button (5) forward and select low speed range, the speed will decrease but will provide

more power and torque.

When using the drill in the high speed range, the speed will increase but will provide less

power and torque. Use the low speed for high power and torque applications and the high

speed for fast drilling applications.

Important: NEVER adjust this two speed selector（3）while the drill is running. Always let it

come to a complete stop.

8.7 LED light (Fig. 8)

The LED work-light（9）can be lit prior to motor running.

Press the on/off switch lightly, to keep the work area lighted.

It also lights during operation.

NOTE: The LED work-light is switched off delayed with about 5 sec.

WARNING:

Do not stare directly at the light beam. Never aim the beam at any person or an object other

than the work piece.

Do not deliberately aim the beam at persons!

8.8 Drilling

Before drilling, the torque setting should be set on the drill position “ ”.

When drilling hard smooth surface, use a centre punch to mark the desired hole location. This

will prevent the drill bit from slipping off centre as the hole is started. Hold the tool firmly and

place the tip of the drill or bit into the work piece, applying only enough pressure to keep the

bit cutting. Do not force or apply side pressure to elongate a hole.

8.8.1 Drilling in wood

For maximum performance, use high speed steel (HSS° drills for wood drilling, turn the torque

setting on the drill position“ ”. Begin drilling at a very low speed to prevent the bit from

slipping off the starting point. Increase the speed as the drill bit bites into the material. When

drilling through holes, place a block of wood behind the work piece to prevent ragged or edges

on the back side of the hole.

8.8.2 Drilling in metal

For maximum performance, use high speed steel (HSS) drill bits for metal or steel drilling.

Turn the torque setting on the drill position“ ”. Begin drilling at a very low speed to prevent

the bit from slipping off the starting point. Maintain a speed and pressure which allows cutting

without overheating the bit. Applying too much pressure will overheat the drill, wear the

bearings, bend or burn bits, produce off-centre or irregular shaped holes.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POWX0026LI Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POWX0026LI

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info