Bedienungsanleitung Powerplus POWX0026LI (Seite 8 von 12) (Englisch)

676177

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

POWX0026LI EN

NOTE: If the battery does not fit properly, disconnect it and confirm that the battery pack is the

correct model for this charger as shown on the specification chart.

Do not charge any other battery pack or any battery pack that does not securely fit the charger.

1. Frequently monitor the charger and battery pack while connected.

2. Unplug the charger and disconnect it from the battery pack when finished.

3. Allow the battery pack to cool completely before using it.

4. Store the charger and battery pack indoors, out of reach of children.

NOTE: If battery is hot after continuous use in the tool, allow it to cool down to room

temperature before charging. This will extend the life of your batteries.

8.2 Removal / insertion of battery (Fig. 3)

WARNING: Before making any adjustments ensure the drill is switched off with the direction of

rotation selector (6) in the centre position.

1 Hold the drill with one hand and the battery pack (7) with the other.

2 To install: pull and slide battery pack into battery port, make sure the latch (8) on the

both side of the battery snap into place and battery is secure before begging operation.

3 To remove: use your thumb and fingers, press the battery release latches in and pull

the battery pack off at the same time.

8.3 Switch On/Off (Fig. 4 & 5)

The drill is started and stopped by depressing and releasing the ON/OFF switch trigger (5).

This cordless drill is equipped with an electric brake, when the ON/OFF switch trigger is

released completely the chuck stops immediately.

8.3.1 Rotation (right/left/lock)

Direction of rotation is controlled by the direction of rotation selector (4) located above the

switch trigger.

Right: To select forward rotation, release the on/off switch and push the forward/reverse lever

to the left side of the tool.

Left: To select reverse rotation, push the lever to the right side of the tool.

Lock: When the selector is in the centre position, the switch trigger is locked. (See Fig. 5)

This helps to reduce the possibility of accidental starting when not in use.

8.3.2 Variable speed

This tool has a variable speed switch that delivers higher speed and torque with increased

trigger pressure. The rotational speed is controlled by the amount of switch trigger depression.

8.4 Installing and Removing a Bit and a Drill (Fig. 6)

This drill has a keyless chuck (1) to prevent the bit or drill from loosening.

1 Hold ring A of the drill chuck tight with one hand.

2 Turn upper ring B anticlockwise with the other hand until the drill chuck opening is large

enough to accept the tool.

3 Insert the drill or the screwdriver bit into the drill chuck.

4 Turn ring B clockwise until the tool is clamped tightly.

Remove the tool in the opposite way.

8.5 Adjusting the torque

The torque is adjusted by rotating the torque setting ring (2); the torque is greater when the

torque setting is set on a higher position. The torque is less when the torque setting ring is set

on a low position. Position “1” denotes the lowest and “ ” denote the highest.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POWX0026LI Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POWX0026LI

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info