Bedienungsanleitung Powerplus POWX0477 (Seite 6 von 11) (Englisch)

645088

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

POWX0477 EN

 Important: after completing sanding, switch off the switch and wait for the coasting sanding

head to stop completely before putting the tool down.

 Never operate the tool in an area with flammable solids, liquids, or gases. Sparks from the

commutator / carbon brushes could cause a fire or explosion.

 There are certain applications for which this tool was designed. The manufacturer strongly

recommends that this tool cannot be modified and / or used for any application other than

for which it was designed.

 Use the machine with both hands at all times. Loss of control can cause personal injury.

 Keep power supply cord clear from the working range of the machine. Always lead the

cable away behind you.

 Immediately switch off the machine if unusual vibrations or if other malfunctions occur.

Check the machine in order to find out the cause.

 The dust that arises when working with this tool can be harmful to health. Use a dust

absorption system and wear a suitable dust protection mask and remove deposited dust

with a vacuum cleaner.

6.1 Electrical connection

The network voltage must conform to the voltage indicated on the tool name plate. Under no

circumstances should the tool be used when the power supply cable is damaged. A damaged

cable must be replaced immediately by an authorized Customer Service Centre. Do not try to

repair the damaged cable yourself. The use of damaged power cables can lead to an electric

shock.

7 ASSEMBLY

Before setting up, repair or maintenance of the appliance you must always

turn off the operating switch and pull out the mains plug!

7.1 Before initial operation

 Check if the rated frequency of the mains supply corresponds to the details of the type

place.

 Before using the tool, read the instruction book carefully.

7.2 Shaft (21)

Fold the front and back part together (Fig. 1-1). Push the folding lock (9) to the right position

and keep the tip adjacent to the handle (Fig. 1-2), and then press the folding lock (9) towards

the handle until the end. (Fig. 1-3)

Unfold the handle by pushing the folding lock to the inside.

7.3 Remove / Assembly sanding head (1 / 2)

 Pull the lock lever and slide to the left to remove the head (Fig. 2-1)

 To assemble the head, firstly ensure the lock lever in release position, then connect the

motor housing (7) and big bearing cove to the head. Push the lock lever up to the right

lock position (Fig. 2-2)

7.4 Replace sanding pad (Fig. 3)

 Insert the hex wrench (size 5) into the hexagonal screw bolt on the sanding block

 Hold the sanding pad firmly, and then turn the wrench counter clockwise to dismount the

pad.

 Install new sanding pad by tightening the bolt.

Attention: Only install the specified sanding pad on the machine.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POWX0477 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POWX0477

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info