Bedienungsanleitung Powerplus POWX0477 (Seite 7 von 11) (Englisch)

645088

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

POWX0477 EN

7.5 Round head and triangle head exchange (Fig. 4)

 Operate the lock lever to release position

 Remove the head (1 / 2)and put the head what you want to use on the machine

 Slide the lock lever into lock position to lock the new head.

Attention: Only install the specified sanding pad on the machine. In order to

ensure optimal performance, the machine should be run at slightly lower

speed for several minutes to make the grinding pad fit the sealing surface

perfectly. During this process, the white foam particles will come out from

the sanding head. However, this won’t damage the machine.

When installing the triangular sanding head, it is possible that this head cannot be pushed all

the way down immediately, because the position of the drive cross head on the sanding pad

does not fully match with the position of the motor.

As a remedy, place the motor housing with the 3 coupling pins in the openings of the sanding

pad. Set the speed control dial to minimum speed. With one hand push the head of the motor

housing down, and with the other hand shortly press in the "on/off switch", until the head of the

motor housing fully engages downwards in the grinding pad.

To fasten the grinding pad to the motor housing, slide the locking lever to the position "locked".

With a round sanding head, the sanding pad can be rotated manually, until the head of the

motor housing is fully engaged in the round sanding pad.

7.5.1 Adjusting the position of the triangular grinding pad (Fig. 10)

Set the selector switch to position "ON" (press down and turn left). Then the sole (bottom) of

the triangular grinding pad can be rotated up to 360 degrees.

Once the desired position has been reached, press in the selector button and turn it to the

right, until the button is in position "OFF".

Move the grinding pad left/right, until the grinding pad engages with a click.

7.5.2 Replacement of the drive cross coupling (Fig. 11)

If needed, the plastic drive cross coupling can be replaced.

This coupling has to be placed over the metal drive of the grind pad.

You can find the replacement couplings (7 items) on top of the grinding pad.

7.6 Attaching and changing sanding tools (Fig. 5)

 Place the sanding tool in the centre of the sanding disc and press on. The holes in the

sanding tool must be in alignment with the extraction holes in the sanding pad.

 For round sanding pad only: conduct a test run to check that the sanding tool is clamped

in the centre.

7.7 Electronic speed control

7.7.1 Adjustable speed

Adjust the speed by turning the speed wheel, user can choose different speed for different

sanding surface.

7.7.2 Constant speed control

Keep the machine running at the same speed as selected. Do not overload by excessive

pressure.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POWX0477 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POWX0477

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info