Bedienungsanleitung Powerplus POWX0561 (Seite 7 von 14) (Englisch)

582664

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

POWX0561 EN

 If the saw blade jams or sawing is interrupted for any reason, release the ON / OFF switch

and calmly hold the saw in the material until the saw blade stands completely still. Never

attempt to remove the saw from the workpiece or pull it backwards as long as the saw

blade is moving or a kickback might occur. Find the cause of the saw blade jam and

eliminate them through appropriate measures.

 When you want to restart a saw that is stuck in a workpiece, center the saw blade in the

saw gap and check that the saw teeth are not stuck in the workpiece. If the saw blade

jams, it can move out from the workpiece or a kickback can happen if the saw is restarted.

 Prop up large panels in order to minimise the risk of a kickback by a jammed saw blade.

Large panels tend to sag under their own weight. Panels must be supported on both sides,

both in the vicinity of the saw gap as well as on the edge.

 Do not use dull or damaged saw blades. Saw blades with blunt or misaligned teeth cause

increased friction, jamming of the saw blade and kickback by an excessively narrow saw

gap.

 Tighten the cutting depth position prior to cutting. If the settings change while cutting, the

saw blade can jam and a kickback can occur.

 Be especially careful if you perform a "circular cut" in a hidden area, such as an existing

wall. The protruding saw blade can get blocked in hidden objects while cutting and cause

a kickback.

 Do not place the saw on the workbench or the floor unless the saw blade is at a standstill.

An unprotected, running saw blade moves the saw against the cutting direction and cuts

whatever is in its way. Thus note the delay time of the saw.

 For this reason, the saw is not suitable for use in reverse position as fixed equipment.

 Do not operate the saw if it is not working properly or has been damaged. In case of

technical problems, do not attempt to repair it on your own. Contact the service or have

the saw repaired by a professional.

8 ADJUSTMENTS

8.1 Plunge saw feature

8.1.1 Selector switch

Use the selector switch (17) to set the respective operation mode.

Change Saw Blade

Plunge Cut

Marked Cut

8.2 Guide rails and clamps (Fig. 1)

The guide rails allow precise and clean straight cuts, miter cuts and fitting. The rails also

protect the work piece surface from damages.

Fixing with the clamps ensures solid grip and safe work.

 Place the guide rail on the work piece and fix the guide rail with the clamps. Slide the bar

into the groove of the guide rail and tighten the clamp with the lever.

 Place the plunge saw on the guide rail. The base plate has a groove (13), which exactly

fits into the guide ridge of the rail.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POWX0561 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POWX0561

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info