Bedienungsanleitung Powerplus POWX0561 (Seite 8 von 14) (Englisch)

582664

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

POWX0561 EN

9 PREPARATION

 Before each use check the proper function of all installation fixtures of the plunge saw and

only use the plunge saw if everything works properly.

 Attach the work piece in such way that it cannot move or bend during work. Line the work

piece respectively.

 Always hold the plunge saw with both hands at the hand grips (3) and (4).

 Always guide the plunge saw forward. Never draw the plunge saw back!

 Place the plunge saw with the front part of the base plate (5) on the work piece. Guide the

plunge saw only against the work piece during operation.

 With the correct forward speed you prevent overheating of the saw blade, and melting

when cutting plastics.

10 OPERATION

10.1 Switching ON/OFF

 Press the switch lock (2) and then the ON/OFF switch (1) to switch the plunge saw on.

 Release the ON/OFF switch (1) to switch the plunge saw off.

Notes: Pressing the switch lock (2) unlocks the plunge cut mechanism at the same time, so

that the blade can be moved downwards. The saw blade emerges from the protective cover.

When lifting the saw the motor slides back into the initial position.

10.2 Setting the cutting depth

The cutting depth can be set between 0 - 54 mm:

 Loosen the cutting depth limit stop knob (9) and slide it to the desired cutting depth

according to the graduated scale (11) to set the cutting depth.

Note: The graduated values on the scale (11) apply for straight cuts (90° cut).

The guide rail depth adjustment stopper (10) must be tilted up when using the plunge saw

without guide rail. Only when using the plunge saw with guide rail, the guide rail depth

adjustment stopper is used to compensate for the thickness of the guide rail.

(Fig 2)

Using the guide rail = guide rail depth adjustment stopper down.

Not using the guide rail = guide rail depth adjustment stopper up.

 (Fig. 3)Tighten the cutting depth limit stop knob (9). The motor or respectively the saw

blade can now be pushed down to the set cutting depth.

For a clean, safe cut set the cutting depth in such way that only max. one saw blade tooth

protrudes under the work piece.

10.3 Setting the cutting angle (Fig. 4)

The plunge saw can be swiveled between 0° and 48°:

 Loosen both rotary knobs (8). Swivel the motor to the desired cutting angle on the cutting

angle scale.

 Tighten the rotary knobs (8) again

Always hold the plunge saw with both hands.

Always guide the plunge saw forward. Never draw the plung saw back!

10.4 Determine Cutting line (Fig. 5)

Two cutting lines are marked on the base plate (5) of the plunge saw.

 Align position A (0 mark on base plate) at the front of the base plate with your marked

cutting line when using the plunge saw without guide rail for straight cuts.

 For 45° miter cuts align position B (45 mark on base plate) at the front of the base plate

with your marked cutting line.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POWX0561 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POWX0561

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info