Bedienungsanleitung Powerplus POWX0760 (Seite 15 von 23) (Englisch)

677891

Zoom out

Zoom in

Vorherige Seite

1/23

Nächste Seite

POWX0760 EN

The tool is shipped from the factory with the set-up in Mitre saw mode.

Before use in table saw mode, change the set up and follow the procedure

below.

9.9.1 Securing the turn table (Fig. 41)

To secure the turn table, tighten the screw firmly on the guide fence at 0° Mitre angle.

9.9.2 Securing the tool head (Fig. 42)

Secure the tool head by tightening the lever in the direction of arrow shown in the figure.

9.9.3 Releasing the lower limit stopper (Fig. 43)

Make sure that the end of the lower limit stopper is at the A position in the figure. Turn the end

of the lower limit stopper counterclockwise to the A position when it is positioned at the B

position.

9.9.4 Repositioning the riving knife (Fig. 44)

The position (Fig. 44-A) should be changed as follows.

(1) Loosen the clamping nut. (Fig. 44-B)

(2) Pull and pivot the riving knife to the position at the angle of 90° in the direction of arrow.

(Fig. 44-C) And push in it slightly so that it become still in this position.

(3) Raise the lower blade guard fully using its lug by hand while pushing the lever nearby the

handle to the left, and release the lever nearby the handle. (Fig. 44-D)

(4) Push the riving knife in the direction of arrow (see Fig. 44-E) so that it is aligned with the

saw blade.

(5) After pushing the riving knife in the direction of arrow shown in the figure, release the lower

blade guard

(6) After aligning the riving knife, tighten the clamping nut securely (see Fig. 44-F).

9.9.5 Removing the lower blade guard (Fig. 45)

Remove the lower blade guardfrom the table by loosening the clamping screw.

9.9.6 Locking the tool head at fully lowered position (Fig. 46)

After setting up the riving knife in position for table saw mode, pull the stopper in the direction

of arrow A and turn it to the angle of 90° in the direction of arrow B with the stopper pulled.

Then lower the handle to lock the tool head.

CAUTION:

 When the tool head cannot be locked in the fully lowered position, turn the depth adjusting

knob by several turns clockwise. (Fig. 47)

 Before turning over the tool, always make sure that the stopper pin has securely locked

the tool head in the lowest position.

9.9.7 Turning over the tool (Fig. 48)

WARNING:

 Make sure that the tool is switched off and unplugged before turning over.

 When pushing down the lever, be sure to place your hand/finger away from the lever-table

fitting area. Hold the middle edge of table with one hand, push the lever down with the

other hand while holding the table edge firmly and pivot the table carefully to turn it over.

Keep holding it until it locks.

9.9.8 Installing the top blade guard (Fig. 49)

Push the push button of the top blade guard to its side surface, place it on the notch of the

riving knife with the button depressed and release the button. After releasing the push button,

make sure that the top blade guard is secured by trying to pull it out.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POWX0760 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POWX0760

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info