Bedienungsanleitung Powerplus POWX0760 (Seite 13 von 23) (Englisch)

677891

Zoom out

Zoom in

Vorherige Seite

1/23

Nächste Seite

POWX0760 EN

The riving knife has been installed before shipment from the factory so that the blade and

riving knife are in a straight line after your simple set-up. Refer to the section titled

“Repositioning riving knife” for the set-up.

CAUTION:

 If the blade and riving knife are not aligned properly, a dangerous pinching condition may

result during operation. Make sure the riving knife is positioned between both outer ends

of the blade teeth when viewing from the top. You could suffer serious personal injury

while using the tool without a properly aligned riving knife. If they are not aligned for any

reasons, always have an authorized service center repair it.

 When adjusting the riving knife clearance from the blade teeth, always loosen the hex bolt

only after loosening the clamping nut.

9.5 Installing and adjusting rip fence (Fig. 28)

 Install the rip fence on the table so that the rip fence holder engages with the guide rail.

Tighten the clamping screw (48) of the rip fence firmly clockwise.

 Loosen the clamping screw (47)

 Slide the rip fence and secure it so that the far end from you of the rip fence is aligned with

the point at which the front edge of saw blade just appears from top surface of the

workpiece. The purpose of this adjustment is to reduce risk of kick-back toward operator

that cut piece from the workpiece is pinched between the saw blade and rip fence and

finally pushed out toward operator. The line A varies by thickness of workpiece or the table

level. Adjust the position of the rip fence according to the thickness of the workpiece. After

adjusting the rip fence, tighten the clamping screw (47) firmly. (Fig. 29)

NOTE:

 There are four patterns to position the rip fence as shown in the figure. Rip fence has two

slits on its sides, one slit with an elevated fringe nearby on the same side and the other

without it. Use the surface of rip fence with this fringe facing the workpiece only when

cutting off into a piece of a thin workpiece.

 To change the rip fence pattern, remove the rip fence from the rip fence holder by

loosening the clamping screw (47) and change the facing of the rip fence to the rip fence

holder so that the rip fence faces the rip fence holder according to your work as shown in

the figure.

 Insert the square nut on the rip fence holder into the back end of either slit of the rip fence

so that they fit as shown in the figure.

 To change from the pattern A or B to the pattern C or D, or in adverse case, remove the

square nut and clamping screw (47) from the rip fence holder, then position the clamping

screw (47) and square nut on the opposite position of the rip fence holder compared to the

original position. Tighten the clamping screw (47) securely after inserting the square nut of

the rip fence holder into the rip fence slit.

Insert the square nut on the rip fence holder into the back end of either slit of the rip fence so

that they fit as shown in the figures. (Fig. 30 & 31)

The rip fence is factory adjusted so that it is parallel to the blade surface. Make sure that it is

parallel. To check to be sure that the rip fence is parallel with the blade, adjust the blade

height with the cutting depth adjusting knob so that the blade appears at the topmost position

from the table. Mark one of the blade teeth with a crayon. Measure the distance (A) and (B)

between the rip fence and blade. Take both measurements using the tooth marked with the

crayon. These two measurements should be identical. If the rip fence is not parallel with the

blade, proceed as follows: (Fig. 32 & 33)

(1) Turn the adjusting screw (55) counterclockwise.

(2) Shift the front edge of the rip fence slightly to right or left until it becomes parallel with the

blade.

(3) Tighten the adjusting screw on the rip fence firmly.

CAUTION:

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POWX0760 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POWX0760

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info