Bedienungsanleitung Powerplus POWX0760 (Seite 12 von 23) (Englisch)

677891

Zoom out

Zoom in

Vorherige Seite

1/23

Nächste Seite

POWX0760 EN

9.2 Table height two-way set up

The table height can be set up in two ways, high or low table.

WARNING: Before falling down the tool backwards, always set the tool in

the Mitre saw mode and lock the tool head in the lowest position.

9.2.1 High table set up (Fig. 18)

To set up the tool with high table, proceed as follows.

 Fall down the tool carefully BACKWARDS without fail while holding it with both hands.

 Fix the 4 legs using a bolt, wing nut and the U-shaped customized washer.

9.2.2 Low table set up (Fig. 19)

 Fold in the 4 legs. To do so :

 Fall down the tool carefully BACKWARDS without fail while holding it with both hands.

 untighten the wing nut of each leg seperatly until you can turn the leg 90° , aligned with

tabel. Then tigthen the wing nut again

 Return the tool to the upright position.

9.3 Installing or removing saw blade

CAUTION:

 Always be sure that the tool is switched off and unplugged before installing or removing

the blade.

 Use only the socket wrench provided to install or remove the blade. Failure to do so may

result in overtightening or insufficient tightening of the hex bolt. This could cause an injury.

Move up the handle in the fully raised position. Press the shaft lock to lock the spindle, use

the socket wrench to loosen the hex bolt clockwise. (Fig. 20) Raise the blade guard A with

its lifting lever while pushing the lever nearby the handle to the left. With the blade guard A

raised, remove the hex bolt, outer flange and blade. (Fig. 21) To install the blade, mount it

carefully onto the spindle, making sure that the direction of the arrow on the surface of the

blade matches the direction of the arrow on the blade case. Install the outer flange and

hex bolt, and then use the socket wrench to tighten the hex bolt (lefthanded) securely

counterclockwise while pressing the shaft lock.

NOTE: When installing a saw blade, be sure to insert it between the blade

guard (7) at first and then raise it so that the blade is finally placed in the

blade guard. (Fig. 22 & 23)

CAUTION:

 The ring 30 mm in outer diameter is factory-installed between the inner and outer flanges.

Return the lower blade guard (8) to its original position. Lower the handle to make sure

that the lower blade guards move properly. Make sure shaft lock has released spindle

before making cut.

9.4 Adjusting riving knife (fig 25,26 & 27)

There must be a clearance of about 5 – 6 mm between the riving knife and the blade teeth

when pushing riving knife toward the blade fully. Adjust the riving knife accordingly by first

loosening clamping nut by hand counterclockwise and then loosening hex bolt

counterclockwise with the hex socket wrench, and measuring the distance. After adjustment,

securely tighten the hex bolt and then the clamping nut clockwise. Always check to see that

the riving knife is secured and that the top blade guard works smoothly before cutting.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POWX0760 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POWX0760

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info