Bedienungsanleitung Powerplus POWX0760 (Seite 10 von 23) (Englisch)

677891

Zoom out

Zoom in

Vorherige Seite

1/23

Nächste Seite

POWX0760 EN

guards are spring loaded so it returns to its original position when the cut is completed and the

handle is raised. The top blade guard falls flat on the table surface after workpiece has passed

under it. NEVER DEFEAT OR REMOVE THE LOWER BLADE GUARDS, THE SPRING

WHICH ATTACHES TO THE LOWER BLADE GUARD, OR THE TOP BLADE GUARD except

for the note below.

In the interest of your personal safety, always maintain each blade guard in good condition.

Any irregular operation of the guards should be corrected immediately. Check to assure spring

loaded return action of the lower blade guards. NEVER USE THE TOOL IF THE LOWER

BLADE GUARD, SPRING OR THE TOP BLADE GUARD ARE DAMAGED, FAULTY OR

REMOVED except for the note below. DOING SO IS HIGHLY DANGEROUS AND CAN

CAUSE SERIOUS PERSONAL INJURY.

NOTE:

There are the following exceptions for removal of guards. Only when using in the table saw

mode, the lower blade guard (8) is removed. Only when using in the Mitre saw mode, the top

blade guard (11) is removed.

 If any of these see-through blade guards becomes dirty, or sawdust adheres to it in such a

way that the blade is no longer easily visible, unplug the saw and clean the guards

carefully with a damp cloth. Do not use solvents or any petroleum-based cleaners on the

plastic guard.

 If the lower blade guard is especially dirty and vision through the guard is impaired,

proceed as follows. Raise the handle fully. Remove the saw blade (Refer to the section

“Installing or removing saw blade”). Raise the lower blade guard while pushing the lever to

the left. With the lower blade guard so positioned, cleaning can be more completely and

efficiently accomplished. When cleaning is complete, reverse procedure above and secure

bolt. In the same case for the top blade guard as above stated, push in the button at its

front to the surface top and remove the top blade guard. After cleaning, always reinstall it

securely.

 If any of these blade guards becomes discolored through age or UV light exposure,

contact our service center for a new guard.

DO NOT DEFEAT OR REMOVE GUARDS.

8.2 Maintaining maximum cutting capacity (Fig. 7)

This tool is factory adjusted to provide the maximum cutting capacity for a 255 mm saw blade.

When installing a new blade, always check the lower limit position of the blade and if

necessary, adjust it as follows:

CAUTION:

When making this adjustment, unplug the tool.

First, unplug the tool. Lower the handle completely. Use the wrench to turn the adjusting bolt

until the periphery of the blade extends slightly below the top surface of the turn table at the

point where the front face of the guide fence meets the top surface of the turn table. With the

tool unplugged, rotate the blade by hand while holding the handle all the way down to be sure

that the blade does not contact any part of the lower base. Readjust slightly, if necessary.

CAUTION:

After installing a new blade, always be sure that the blade does not contact any part of the

lower base when the handle is lowered completely. Always do this with the tool unplugged.

This tool can be used with or without the lower limit by shifting the lower limit stopper as

shown in the figure. (Fig. 8 - 15)

To use the tool without the lower limit, turn the stopper end counterclockwise. Use in this

position is proper to cut a wide and thin workpiece.

To use the tool with the lower limit, move the stopper end clockwise. Use in this position is

proper to cut a thick workpiece.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POWX0760 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POWX0760

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info