Bedienungsanleitung Powerplus POWX0760 (Seite 9 von 23) (Englisch)

677891

Zoom out

Zoom in

Vorherige Seite

1/23

Nächste Seite

POWX0760 EN

 Make sure that the turn table is fixed securely.

 Make sure that the arm is securely fixed in the working position. Tighten the lever

clockwise to fix the arm.

 Use (6) push stick or (6) push block to avoid working with the hands and fingers close to

the saw blade.

 Make sure the blade is not contacting the riving knife or workpiece before the switch is

turned on.

 Always store the push-stick when it is not in use.

 Pay particular attention to instructions for reducing risk of KICKBACK. KICKBACK is (6)

sudden reaction to (6) pinched, bound or misaligned saw blade. KICKBACK causes the

ejection of the workpiece from the tool back towards the operator. KICKBACKS CAN

LEAD TO SERIOUS PERSONAL INJURY. Avoid KICKBACKS by keeping the blade

sharp, by keeping the rip fence parallel to the blade, by keeping the riving knife and blade

guard in place and operating properly, by not releasing the workpiece until you have

pushed it all the way past the blade, and by not ripping (6) workpiece that is twisted or

warped or does not have (6) straight edge to guide along the fence.

 Avoid abrupt, fast feeding. Feed as slowly as possible when cutting hard workpieces. Do

not bend or twist workpiece while feeding. If you stall or jam the blade in the workpiece,

turn the tool off immediately. Unplug the tool. Then clear the jam.

 Before turning over the tool, always make sure that the stopper pin has securely locked

the tool head in the lowest position.

7 INSTALLATION

CAUTION: Keep the floor area around the tool level, well maintained and

free of loose materials e.g. chips and cut-offs.

7.1 Bench mounting (Fig. 1 & 3)

7.1.1 For the fully-extended feet set up as the high table.

When the tool cannot be set up stable, turn the adjusting nut at the foot of the tool for proper

stability. Turn counterclockwise in top viewing to make the foot shorter and clockwise in top

viewing to make it longer. After adjustment, make sure that the tool keep stable.

7.1.2 For the folded feet set up as the low table

When the tool is ready in the foot-folded position, secure the tool by using U-shaped grooves

shown in the figure. (fig 3 (5) )

8 FUNCTIONAL DESCRIPTION

CAUTION: Always be sure that the tool is switched off and unplugged

before adjusting or checking function on the tool.

8.1 Blade guard (Fig. 4, 5 & 6)

Caution:

 Make sure that the handle cannot be lowered without pushing the lever nearby the handle

to the left. (fig 2 - 20)

 Make sure that the lower blade guards A dose not open unless the lever near the handle

is pushed at the topmost position of the handle.

 Make sure that the lower blade guard C is installed before using in Mitre saw mode.

When lowering the handle while pushing the lever to the left, the lower blade guard A rises

automatically. The lower blade guard B rises as it contacts a workpiece. The lower blade

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POWX0760 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POWX0760

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info