Bedienungsanleitung Powerplus POWX0761 (Seite 10 von 24) (Englisch)

481033

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

POWX0761 EN

8 FUNCTIONAL DESCRIPTION

CAUTION: Always be sure that the tool is switched off and unplugged

before adjusting or checking function on the tool.

8.1 Blade guard (Fig. 4, 5 & 6)

Caution:

 Make sure that the handle cannot be lowered without pushing the lever nearby the handle

to the left. (fig 2 - 20)

 Make sure that the lower blade guards A dose not open unless the lever near the handle is

pushed at the topmost position of the handle.

 Make sure that the lower blade guard C is installed before using in Mitre saw mode.

When lowering the handle while pushing the lever to the left, the lower blade guard A rises

automatically. The lower blade guard B rises as it contacts a workpiece. The lower blade

guards are spring loaded so it returns to its original position when the cut is completed and the

handle is raised. The top blade guard falls flat on the table surface after workpiece has passed

under it. NEVER DEFEAT OR REMOVE THE LOWER BLADE GUARDS, THE SPRING

WHICH ATTACHES TO THE LOWER BLADE GUARD, OR THE TOP BLADE GUARD except

for the note below.

In the interest of your personal safety, always maintain each blade guard in good condition.

Any irregular operation of the guards should be corrected immediately. Check to assure spring

loaded return action of the lower blade guards. NEVER USE THE TOOL IF THE LOWER

BLADE GUARD, SPRING OR THE TOP BLADE GUARD ARE DAMAGED, FAULTY OR

REMOVED except for the note below. DOING SO IS HIGHLY DANGEROUS AND CAN

CAUSE SERIOUS PERSONAL INJURY.

NOTE:

There are the following exceptions for removal of guards. Only when using in the table saw

mode, the lower blade guard (8) is removed. Only when using in the Mitre saw mode, the top

blade guard (11) is removed.

 If any of these see-through blade guards becomes dirty, or sawdust adheres to it in such a

way that the blade is no longer easily visible, unplug the saw and clean the guards carefully

with a damp cloth. Do not use solvents or any petroleum-based cleaners on the plastic

guard.

 If the lower blade guard is especially dirty and vision through the guard is impaired, proceed

as follows. Raise the handle fully. Remove the saw blade (Refer to the section “Installing or

removing saw blade”). Raise the lower blade guard while pushing the lever to the left. With

the lower blade guard so positioned, cleaning can be more completely and efficiently

accomplished. When cleaning is complete, reverse procedure above and secure bolt. In the

same case for the top blade guard as above stated, push in the button at its front to the

surface top and remove the top blade guard. After cleaning, always reinstall it securely.

 If any of these blade guards becomes discolored through age or UV light exposure, contact

our service center for a new guard.

DO NOT DEFEAT OR REMOVE GUARDS.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POWX0761 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POWX0761

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info