Bedienungsanleitung Powerplus POWX0761 (Seite 11 von 24) (Englisch)

481033

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

POWX0761 EN

8.2 Maintaining maximum cutting capacity (Fig. 7)

This tool is factory adjusted to provide the maximum cutting capacity for a 255 mm saw blade.

When installing a new blade, always check the lower limit position of the blade and if

necessary, adjust it as follows:

CAUTION:

When making this adjustment, unplug the tool.

First, unplug the tool. Lower the handle completely. Use the wrench to turn the adjusting bolt

until the periphery of the blade extends slightly below the top surface of the turn table at the

point where the front face of the guide fence meets the top surface of the turn table. With the

tool unplugged, rotate the blade by hand while holding the handle all the way down to be sure

that the blade does not contact any part of the lower base. Readjust slightly, if necessary.

CAUTION:

After installing a new blade, always be sure that the blade does not contact any part of the

lower base when the handle is lowered completely. Always do this with the tool unplugged.

This tool can be used with or without the lower limit by shifting the lower limit stopper as

shown in the figure. (Fig. 8 - 15)

To use the tool without the lower limit, turn the stopper end counterclockwise. Use in this

position is proper to cut a wide and thin workpiece.

To use the tool with the lower limit, move the stopper end clockwise. Use in this position is

proper to cut a thick workpiece.

8.3 Adjusting the Mitre angle (Fig. 9 & 10)

Loosen the clamping screw on the guide fence by turning counterclockwise. Turn the turn

table by handle. When you have moved the handle to the position where the pointer points to

the desired angle on the Mitre scale, securely tighten the clamping screw clockwise.

CAUTION:

 When turning the turn table, be sure to raise the handle fully.

 After changing the Mitre angle, always secure the turn table by tightening the clamping

screw firmly.

8.4 Adjusting the bevel angle (Fig. 11 & 12)

8.4.1 In the Mitre saw mode

To adjust the bevel angle, loosen the lever at the rear of the tool counterclockwise. Push the

handle to the left to tilt the saw blade until the pointer points to the desired angle on the bevel

scale. Then tighten the lever clockwise firmly to secure the arm.

CAUTION:

 When tilting the saw blade, be sure to raise the handle fully.

 After changing the bevel angle, always secure the arm by tightening the lever clockwise.

8.4.2 In the table saw mode (Fig. 13)

To adjust the bevel angle, loosen the lever under the table at the front of the tool

counterclockwise. Move the depth adjusting knob to the left to tilt the saw blade until the

pointer points to the desired angle on the bevel scale. Then tighten the lever clockwise firmly

to secure the arm.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POWX0761 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POWX0761

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info