Bedienungsanleitung Powerplus POWX0761 (Seite 13 von 24) (Englisch)

481033

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

POWX0761 EN

9.2.2 Low table set up (Fig. 19)

 Fold in the 4 legs. To do so :

 Fall down the tool carefully BACKWARDS without fail while holding it with both hands.

 untighten the wing nut of each leg seperatly until you can turn the leg 90° , aligned with

tabel. Then tigthen the wing nut again

 Return the tool to the upright position.

9.3 Installing or removing saw blade

CAUTION:

 Always be sure that the tool is switched off and unplugged before installing or removing the

blade.

 Use only the socket wrench provided to install or remove the blade. Failure to do so may

result in overtightening or insufficient tightening of the hex bolt. This could cause an injury.

Move up the handle in the fully raised position. Press the shaft lock to lock the spindle, use

the socket wrench to loosen the hex bolt clockwise. (Fig. 20) Raise the blade guard A with

its lifting lever while pushing the lever nearby the handle to the left. With the blade guard A

raised, remove the hex bolt, outer flange and blade. (Fig. 21) To install the blade, mount it

carefully onto the spindle, making sure that the direction of the arrow on the surface of the

blade matches the direction of the arrow on the blade case. Install the outer flange and hex

bolt, and then use the socket wrench to tighten the hex bolt (lefthanded) securely

counterclockwise while pressing the shaft lock.

NOTE: When installing a saw blade, be sure to insert it between the blade

guard (7) at first and then raise it so that the blade is finally placed in the

blade guard. (Fig. 22 & 23)

CAUTION:

 The ring 30 mm in outer diameter is factory-installed between the inner and outer flanges.

Return the lower blade guard (8) to its original position. Lower the handle to make sure that

the lower blade guards move properly. Make sure shaft lock has released spindle before

making cut.

9.4 Adjusting riving knife (fig 25,26 & 27)

There must be a clearance of about 5 – 6 mm between the riving knife and the blade teeth

when pushing riving knife toward the blade fully. Adjust the riving knife accordingly by first

loosening clamping nut by hand counterclockwise and then loosening hex bolt

counterclockwise with the hex socket wrench, and measuring the distance. After adjustment,

securely tighten the hex bolt and then the clamping nut clockwise. Always check to see that

the riving knife is secured and that the top blade guard works smoothly before cutting.

The riving knife has been installed before shipment from the factory so that the blade and

riving knife are in a straight line after your simple set-up. Refer to the section titled

“Repositioning riving knife” for the set-up.

CAUTION:

 If the blade and riving knife are not aligned properly, a dangerous pinching condition may

result during operation. Make sure the riving knife is positioned between both outer ends of

the blade teeth when viewing from the top. You could suffer serious personal injury while

using the tool without a properly aligned riving knife. If they are not aligned for any reasons,

always have an authorized service center repair it.

 When adjusting the riving knife clearance from the blade teeth, always loosen the hex bolt

only after loosening the clamping nut.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POWX0761 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POWX0761

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info