Bedienungsanleitung Powerplus POWX0761 (Seite 15 von 24) (Englisch)

481033

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

POWX0761 EN

9.6 Installing and adjusting Mitre gauge (Fig. 35)

Install the Mitre gauge by inserting its shaft into one of two grooves in the table from the front.

Mitre gauge fence that is also used as rip fence can be installed on the Mitre gauge according

to your work.

9.7 Dust bag (Fig 36, 37 & 38)

The use of the dust bag makes cutting operations clean and dust collection easy. To attach

the dust bag, fit it onto the dust nozzle.

When the dust bag is about half full, remove the dust bag from the tool and pull the fastener

out. Empty the dust bag of its contents, tapping it lightly so as to remove particles adhering to

the insides which might hamper further collection.

If you connect a vacuum cleaner to your saw, more efficient and cleaner operations can be

performed.

9.8 Securing workpiece

WARNING It is extremely important to always secure the workpiece

properly and tightly with the vise. Failure to do so can cause the tool to be

damaged and/or the workpiece to be destroyed. PERSONAL INJURY MAY

ALSO RESULT. Also, after a cutting operation, DO NOT raise the blade until

the blade has come to a complete stop.

Vertical vise (Fig. 40)

The vertical vise can be installed in two positions on either the left or right side of the guide

fence. Insert the vise rod into the hole in the guide fence and tighten the clamping screw to

secure the vise rod. Position the vise arm according to the thickness and shape of the

workpiece and secure the vise arm by tightening the clamping screw. If the screw to secure

the vise arm contacts the guide fence, install the clamping screw on the opposite side of vise

arm. Make sure that no part of the tool contacts the vise when lowering the handle all the way.

If some part contacts the vise, re-position the vise. Press the workpiece flat against the guide

fence and the turn table. Position the workpiece at the desired cutting position and secure it

firmly by tightening the vise knob.

CAUTION:

 The workpiece must be secured firmly against the turn table and guide fence.

9.9 Setting up the tool in table saw mode

CAUTION:

 Before use in the table saw mode, make sure that the turn table has been secured at 0°

Mitre angle with the clamping screw on the guide fence.

 Before use in the table saw mode, make sure that the tool head has been secured with the

lever.

 Before use in the table saw mode, make sure that the riving knife has been secured in

place properly.

 Before use in the table saw mode, remove the lower blade guard (8)

 In table saw mode, release the lower limit stopper.

The tool is shipped from the factory with the set-up in Mitre saw mode.

Before use in table saw mode, change the set up and follow the procedure

below.

9.9.1 Securing the turn table (Fig. 41)

To secure the turn table, tighten the screw firmly on the guide fence at 0° Mitre angle.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POWX0761 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POWX0761

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info