Bedienungsanleitung Powerplus POWX0761 (Seite 18 von 24) (Englisch)

481033

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

POWX0761 EN

10 OPERATION

CAUTION:

 Before use, be sure to release the handle from the lowered position by pulling the stopper

pin and turning it to the angle of 90°.

 Make sure the blade is not contacting the workpiece, etc. before the switch is turned on.

10.1 Cutting as mitre saw

WARNING: Make sure that the lower blade guard C is installed before using

in Mitre saw mode.

CAUTION:

 Do not apply excessive pressure on the handle when cutting. Too much force may result in

overload of the motor and/or decreased cutting efficiency. Push down handle with only as

much force as is necessary for smooth cutting and without significant decrease in blade

speed.

 Gently press down the handle to perform the cut. If the handle is pressed down with force or

if lateral force is applied, the blade will vibrate and leave a mark (saw mark) in the

workpiece and the precision of the cut will be impaired.

10.1.1 Press cutting

Secure the workpiece against guide fence and turn table. Switch on the tool without the blade

making any contact and wait until the blade attains full speed before lowering. Then gently

lower the handle to the fully lowered position to cut the workpiece. When the cut is completed,

switch off the tool and WAIT UNTIL THE BLADE HAS COME TO A COMPLETE STOP before

returning the blade to its fully elevated position.

10.1.2 Mitre cutting

Refer to the previously covered “Adjusting the Mitre angle”.

10.1.3 Bevel cut

Loosen the lever and tilt the saw blade to set the bevel angle (Refer to the previously covered

“Adjusting the bevel angle”). Be sure to retighten the lever firmly to secure the selected bevel

angle safely. Secure the workpiece against guide fence and turn table. Switch on the tool

without the blade making any contact and wait until the blade attains full speed. Then gently

lower the handle to the fully lowered position while applying pressure in parallel with the blade.

When the cut is completed, switch off the tool and WAIT UNTIL THE BLADE HAS COME TO

A COMPLETE STOP before returning the blade to its fully elevated position.

CAUTION:

 Always be sure that the blade will move down to bevel direction during a bevel cut. Keep

hands out of path of saw blade.

 During a bevel cut, it may create a condition whereby the piece cut off will come to rest

against the side of the blade. If the blade is raised while the blade is still rotating, this piece

may be caught by the blade, causing fragments to be scattered which is dangerous. The

blade should be raised ONLY after the blade has come to a complete stop.

 When pressing the handle down, apply pressure parallel to the blade. If the pressure is not

parallel to the blade during a cut, the angle of the blade might be shifted and the precision

of the cut will be impaired.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POWX0761 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POWX0761

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info