Bedienungsanleitung Powerplus POWX0761 (Seite 19 von 24) (Englisch)

481033

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

POWX0761 EN

10.1.4 Compound cutting

Compound cutting is the process in which a bevel angle is made at the same time in which a

Mitre angle is being cut on a workpiece. Compound cutting can be performed at angle shown

in the table.

Bevel angle

Miter angle

45°

Left and Right 0 – 45°

When performing compound cutting, refer to “Press cutting”, “Mitre cutting” and “Bevel cut”

explanations.

10.1.5 Cutting aluminum extrusion (Fig. 56)

When securing aluminum extrusions, use spacer blocks or pieces of scrap as shown in the

figure to prevent deformation of the aluminum. Use a cutting lubricant when cutting the

aluminum extrusion to prevent buildup of the aluminum material on the blade.

CAUTION:

 Never attempt to cut thick or round aluminum extrusions. Thick aluminum extrusions may

come loose during operation and round aluminum extrusions cannot be secured firmly with

this tool.

 Never cut aluminum in the table saw mode (bench mode).

10.2 Cutting as table saw (bench mode)

CAUTION:

 Always use “work helpers” such as push sticks and push blocks when there is a danger that

your hands or fingers will come close to the blade.

 Always hold the workpiece firmly with the table and the rip fence. Do not bend or twist it

while feeding. If the workpiece is bent or twisted, dangerous kickbacks may occur.

 NEVER withdraw the workpiece while the blade is running. If you must withdraw the

workpiece before completing a cut, first switch the tool off while holding the workpiece

firmly. Wait until the blade has come to a complete stop before withdrawing the workpiece.

Failure to do so may cause dangerous kickbacks.

 NEVER remove cut-off material while the blade is running.

 NEVER place your hands or fingers in the path of the saw blade.

 Always secure the rip fence firmly, or dangerous kickbacks may occur.

 Always use “work helpers” such as push sticks and push blocks when cutting small or

narrow workpieces, or when the ado head is hidden from view while cutting.

10.2.1 Work helpers

Push sticks, push blocks or auxiliary fence are types of “work helpers”. Use them to make safe,

sure cuts without the need for the operator to contact the blade with any part of the body.

10.2.2 Push block (Fig. 57)

Use a 19 mm piece of plywood. Handle should be in center of plywood piece. Fasten with glue

and wood screws as shown. Small piece 9.5 mm x 8 mm x 50 mm of wood must always be

glued to plywood to keep the blade from dulling if the operator cuts into push block by mistake.

(Never use nails in push block.)

10.2.3 Auxiliary fence (Fig. 58)

Make auxiliary fence from 9.5 mm and 19 mm plywood pieces.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POWX0761 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POWX0761

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info